Tel
Tel
+8618142863185
Follow us
Official Accounts
Official Accounts
- Top
Evaluation and Quality Control of UV Resins
Release time:
2014-06-27 14:32
Evaluation and Quality Control of UV Resins:
I. Evaluation Criteria for UV Resins
1. Types and basic structural composition of resins
2. Average functionality
3. Adhesion, weather resistance, acid and alkali resistance, chemical resistance
4. Hardness, wear resistance, flexibility, and elongation at break
5. Solubility in solvents or monomers, as well as compatibility with other resins.
6. Storage Stability
7. Quality Stability Between Batches
8. Procurement channels and cost-effectiveness
II. Quality Control Indicators for UV Resins
1. Appearance and color
2. Viscosity
3. Acid value
4. Solid Content
5. Resistance to high and low temperatures and storage stability
6. Average Molecular Weight and Its Molecular Weight Distribution
7. Glass transition temperature (℃)
8. Acrylic double-bond density (mmol/g)
III. Quality Control Indicators and Methods for UV Resins
1. Quality control methods for the appearance and color of UV resin
(1) UV resin typically appears as a viscous, transparent liquid.
(2) The color detection methods for UV resins include:
a. Iron-cobalt colorimetric method: Gardner units
b. Platinum-cobalt colorimetric method: APHA units
2. Quality control method for UV resin viscosity:
(1) Viscosity is a measure of a liquid's resistance to flow; the higher the viscosity, the poorer the liquid's flowability.
(2) The viscosity of UV resins is typically measured using a rotational viscometer, with units expressed in cps/℃. Common test temperatures are 25℃ and 60℃.
(3) Control of Viscosity Test Errors

3. Quality control methods for acid value and solid content
(1) The quality control of resin acid value is performed using the titration method with a standard KOH solution, with the unit being mg KOH/g.
(2) The quality control of the solid content in the resin is performed using a high-temperature baking test. Our company’s implementation protocol involves baking at 110℃ for 2 hours in an oven.
4. Quality control methods for resin’s resistance to high and low temperatures and storage stability
(1) UV resin can undergo a polymerization reaction under heating conditions; it is recommended to test its high-temperature stability at 120℃.
(2) At low temperatures below -25℃, UV resin typically transitions from a liquid state to a solid or semi-solid state; upon reheating, it returns to a liquid state. Use this property to check whether the resin exhibits a microgel effect.
(3) Where conditions permit, it is recommended to conduct a high- and low-temperature cyclic impact test ranging from -40°C to 120°C.
(4) The storage stability test for UV resins generally requires aging in a 60℃ oven for 2 weeks, followed by storage at room temperature for 6 months without gelation.
5. Average Molecular Weight and Molecular Weight Distribution of UV Resins
(1) UV resins are oligomers with molecular weights ranging from several hundred to several thousand. Their molecular weights exhibit polydispersity and can only be described using average molecular weights, which are categorized into number-average molecular weight (Mn) and weight-average molecular weight (Mw).
(2) Molecular Weight Distribution (MWD):
MWD = Mw/Mn
The larger the MWD, the wider the molecular weight distribution.

6. Glass transition temperature (Tg) of UV resin
(1) The glass transition temperature is the temperature at which chain segments in polymer molecules begin to move.
(2) The glass transition temperature (Tg) of a resin is directly determined by its molecular structure.
(3) The more flexible the polymer backbone, the lower the glass transition temperature;
(4) Generally speaking, the glass transition temperature (Tg) of a resin increases with increasing average molecular weight (within a certain range).
(5) Tg increases as the molecular weight distribution widens;
(6) The glass transition temperature (Tg) of resins is typically determined using a differential scanning calorimeter (DSC).
7. Average functionality and double-bond density of UV resin
(1) The functionality refers to the number of acrylic double bonds contained in a low-molecular-weight polymer chain. Since UV resins are generally mixtures, the term "functionality" actually refers to the average functionality.
(2) The double-bond density of UV resin can be understood as the number of acrylate double bonds contained per unit weight of resin, with the unit being mmol/g. The double-bond density is directly proportional to the curing rate of the UV resin.
(3) The average functionality of a UV resin is not equivalent to the double-bond density of the resin; the double-bond density is also influenced by the resin’s average molecular weight and specific gravity.
(4) The methods for determining the density of acrylic double bonds in UV resins include chemical titration, FTIR, and 1H NMR.
Summary:
(1) The molecular structure and intrinsic properties of a resin determine its external performance; synthetic resins are designed starting from their molecular structure.
(2) The resin’s appearance and color, viscosity, acid value, solid content, storage stability, average molecular weight and its distribution, Tg, and double-bond density can all serve as effective quality-control indicators for the resin. The stability of the measured values for each of these indicators directly reflects the batch-to-batch consistency of the resin and is crucial for controlling the quality of the finished product.
(3) It is recommended that manufacturers of UV resins establish resin quality control standards and conduct testing on key indicators to facilitate product quality control.
Share to:
Related News
How to Enhance the Adhesion of UV Coatings
The adhesion of UV coatings is a critical factor affecting their spray-coating quality. In practical applications, differences in substrate materials, variations in coating thickness, and factors such as the power of UV curing can all lead to insufficient bonding between the coating and the substrate, resulting in issues like paint chipping and failure to pass testing. To address these problems, it is possible to enhance the adhesion between the coating and the substrate through appropriate pre-treatment measures.
What should I do if UV resin/coating exhibits gelation? And what are the precautions to take?
In the coatings industry, it’s common for some customers to report gelation issues with UV resins or UV coatings. There are multiple factors that can cause UV resin gelation, and when troubleshooting this problem, it’s important to systematically rule out each potential cause one by one. So, what should you do if your UV resin or UV coating experiences gelation? What precautions should you take? Let’s take a closer look at the causes of gelation below.
Synthesis and Properties of Polyurethane Acrylate (PUA)
Polyurethane acrylate (PUA) is an important material characterized by excellent surface gloss, hardness, adhesion, and flexibility, as well as outstanding resistance to yellowing. Its wide range of applications gives it promising market prospects and significant development potential.