Tel
Tel
+8618142863185
Follow us
Official Accounts
Official Accounts
- Top
How to Enhance the Adhesion of UV Coatings
Release time:
2014-06-26 13:50
The adhesion of UV coatings includes the adhesion between the primer and the substrate, as well as the adhesion between the primer and the topcoat.
I. Adhesion between the primer and the substrate
Generally, UV coatings exhibit good adhesion to wood, bamboo, PVC plastic, ABS plastic, and certain metals.
II. Adhesion between the topcoat and the primer
UV coatings have poor interlayer adhesion, which is a major drawback of UV coatings. The primary solution to the issue of interlayer adhesion in UV coatings lies in sanding. Therefore, for manufacturers of bamboo and wood flooring, if the sanding process for the primer coat is not handled properly, it can easily lead to quality defects. If the primer coat is not sanded thoroughly enough, the bond between the primer and the surface will be weak. After being left in the air for some time, moisture can seep into the space between the primer and the surface, causing bubbling in the topcoat. If you peel off the topcoat film, you’ll notice tiny water droplets condensing on the primer layer. Over time, the entire topcoat may completely peel off, resulting in a serious quality failure. For this reason, it’s crucial to pay special attention to the sanding of the primer coat.
For some manufacturers, board deformation is relatively severe, and after applying the primer, it’s inevitable that certain areas of the paint surface won’t be adequately sanded. In such cases, how can we address the adhesion issue between the primer and the topcoat? Based on our experimental experience, we can control the degree of curing of the primer to resolve this problem. Specifically, we should aim for the primer to reach a semi-dry (surface-dry) state—just enough so that a fingernail can leave a faint white mark when lightly scratched. This approach ensures that sanding isn’t hindered while simultaneously enhancing the bond between the primer and the topcoat. Generally speaking, for Taiwanese equipment, when the lamp distance is 15 cm, only three low-intensity lamps need to be turned on. The specific settings, however, must be adjusted according to each manufacturer’s unique lighting conditions. In short, the primer should not be allowed to fully cure, whereas the topcoat must be completely cured.
III. Adhesion between UV Coating and Other Coatings
The adhesion between UV coatings and other baked or self-drying paints generally requires special treatment methods.
IV. Methods for Adhesion Testing
Generally, grid tests are performed on actual substrate coating samples according to the GB 9286-88 standard. For single-layer coatings, the grid spacing is 1 mm—meaning that within a 1 cm area, the coating is scored into 100 small squares using a blade (or a grid cutter). The resulting coating is then evaluated by applying transparent adhesive tape and assessing the degree of paint film detachment. For multi-layer coatings, the grid spacing should be increased to 2–3 mm, depending on the thickness of the coating film.
Share to:
Related News
What should I do if UV resin/coating exhibits gelation? And what are the precautions to take?
In the coatings industry, it’s common for some customers to report gelation issues with UV resins or UV coatings. There are multiple factors that can cause UV resin gelation, and when troubleshooting this problem, it’s important to systematically rule out each potential cause one by one. So, what should you do if your UV resin or UV coating experiences gelation? What precautions should you take? Let’s take a closer look at the causes of gelation below.
Synthesis and Properties of Polyurethane Acrylate (PUA)
Polyurethane acrylate (PUA) is an important material characterized by excellent surface gloss, hardness, adhesion, and flexibility, as well as outstanding resistance to yellowing. Its wide range of applications gives it promising market prospects and significant development potential.
Introduction to Epoxy Acrylate
Epoxycrylates (EA) are a class of prepolymers widely used in the UV-curing field. The following provides an introduction to several commonly used epoxycrylates (EA) in the UV-curing domain, covering their structure, properties, and applications.