Tel
Tel
+8618142863185
Follow us
Official Accounts
Official Accounts
- Top
Design Concept and Application & Construction Control of UV Coating Formulations for Enclosures
Release time:
2016-04-28 14:35
I. Purpose of UV Varnish Application
1. Protection of the primer;
2. Enhance the mechanical properties of the coating film’s appearance;
3. Rapid curing;
4. Significant savings in energy and production space.
II. Classic Pyramid Structure Diagram

III. Selection of Oligomers
1. 6-9 official polyurethane
(1) Rapid curing;
(2) High wear resistance;
(3) High crosslinking degree;
(4) High hardness;
(5) Recommendations: B-618, B-615, B-619, B-619W, B-675, B-908, B-910A2, B-919B.
2. 2-3-component polyurethane
(1) Enhance the fullness of the paint film;
(2) Adjust flexibility;
(3) Plays an auxiliary role in the formulation;
(4) Recommendations: B-205, B-216, B-375.
3. Bisphenol A epoxy resin
(1) This system features fast curing speed, high hardness, and low cost, making it suitable as a main resin.
(2) Wear resistance and resistance to boiling water may occasionally be slightly affected;
(3) Serve as auxiliary filling;
(4) Recommendations: B-100, B-102, B-105M, B-102M.
4. Special functional group acrylates
(1) Reduce curing shrinkage and enhance interlayer adhesion;
(2) Improve workability and enhance surface cleanliness;
(3) As an auxiliary agent for regulating resin action;
(4) Recommendations: B-6350, B-6371-3, B-6380N, B-6380NY, B-6580, B-6315A.
5. Monomer
(1) High-functional monomers: Increase cross-linking density; e.g., DPHA, TMPTA, PET3A.
(2) Low-molecular-weight monomers: Reduce shrinkage and improve interlayer adhesion; examples include: HEMA, IBOA, EOEOEA.
(3) Specialty monomers: Improve adhesion, especially on metal substrates; for example, phosphate esters (B-02) enhance the density of the formed film.
6. Other ingredients

IV. Formulation Structure of the Spraying System
1. Achieve atomized spray application with a 1.5mm nozzle diameter under a pressure of 3kg;
2. Coating viscosity: 8–12 s (NK-2# at 25℃);
Note: For spray viscosities within this range, in coating systems primarily based on PUA, the diluent proportion should reach 50% to 70%, meaning the solid content of the formulation will be between 30% and 50%.
V. Principles for Preparing Diluents
1. Primarily characterized by strong solubility and low boiling point;
2. Using a high-boiling point as an auxiliary, it assists the flow of the wet film and improves its appearance.
3. Using a reasonable evaporation gradient as the framework, allow the solvent to be released in an orderly manner;
4. When selecting a solvent, try to avoid solvents that readily absorb moisture.
VI. Design Principles for Formulations
1. Select a resin that is suitable based on the customer’s specifications.
2. Based on the UV curing principle, make a reasonable combination.
3. Consider both conventional drying and curing conditions, as well as the broadest possible construction conditions, such as leveling, temperature, time, and UV energy levels.
4. For construction features such as planar spraying, facade rotary spraying, and structural anomalies, assess potential construction defects and effectively implement corresponding measures.
7. Establish quality control standards
1. Control of the production feeding and dispersion process flow;
2. Wet products: appearance, viscosity;
3. Dry Film: Consistent testing standards, standardization of testing equipment and methods, general-purpose products—point-to-surface; case-specific products—point-to-point.
8. Customer Complaint Handling
1. In principle, mass-produced products that have been launched have already undergone rigorous testing against all standards in both the initial trial and the pilot-scale trials.
2. Most customer complaints regarding mass production are caused by changes in production conditions—such as abnormalities in material batches or deviations in temperature and humidity—often due to objective factors and operational practices. Technical service personnel typically have extensive experience in handling such issues.
9. Summary
1. Formulation Design: First, you must have a thorough understanding of the properties of the raw materials and a solid grasp of the characteristics of both the primer and the substrate material.
2. Secondly, become familiar with the customer’s production process conditions.
3. Finally, based on the testing standards, scientifically and reasonably select materials and design application formulations that offer excellent cost performance.
Share to:
Related News
Oxygen inhibition in UV curing
After UV adhesive is cured by ultraviolet light irradiation, a sticky surface phenomenon may occur—known as oxygen inhibition. The primary cause of this phenomenon is the free-radical polymerization process. Typically, the UV curing process takes place in air, during which oxygen from the atmosphere gradually diffuses into the coating film. This oxygen competes with the free-radical polymerization reaction, effectively consuming the free radicals. As a result, the curing time of the adhesive is prolonged: while the bottom layer of the coating has already cured, the surface layer remains largely uncured, leading to the sticky appearance on the adhesive’s surface.
The Printing Process (Part 2): Printing Methods
Printing methods can be classified according to the relative positions of image and non-image areas on the printing plate. The common printing techniques can be broadly divided into four major categories: letterpress printing, offset printing, gravure printing, and screen printing. It is essential to select the appropriate printing method based on the requirements of the printed material in order to achieve the desired results.
The Art of Printing (I): An Encyclopedia of Printing
Printing is a technology that involves transferring ink onto the surfaces of materials such as paper, textiles, plastics, and leather through processes including plate-making, inking, and applying pressure, thereby mass-replicating the content of original manuscripts—be it text, illustrations, photographs, or anti-counterfeiting elements.