Tel
Tel
+8618142863185
Follow us
Official Accounts
Official Accounts
- Top
Oxygen inhibition in UV curing
Release time:
2016-04-25 13:52
I. Mechanism of Oxygen Inhibition of Polymerization
1. Schematic diagram of free-radical oxygen inhibition:

2. Mechanism of oxygen inhibition:
(1) Oxygen-sensitive initiators (PIs) for the quenching of photoexcited states;
(2) Reacts with the initiator to generate free radicals (R•) or chain-propagating free radicals, which then react with propagating free radicals (P-M•) to form peroxyl radicals (POO•).
Instructions:
The first category is reducing oxygen inhibition during the photoinitiation stage.
The second category of strategies (f and g) involves introducing a hydrogen donor (DH) and a reducing agent (RA), which promote the chain transfer of peroxyl radicals and generate more reactive radicals (D• or PO•).
Category 3 (h) can attempt to decompose peroxides or alkyl peroxides to generate more reactive free radicals.
II. Physical Methods to Inhibit Oxygen-Induced Polymerization Inhibition
1. Curing in an anaerobic atmosphere
(1) Inert atmosphere protection is the earliest and most widely used method for preventing oxygen from diffusing into the polymerization system; however, equipment and process limitations have made it difficult to promote its widespread adoption.
(2) Helium: Has higher diffusivity than nitrogen and is more effective at displacing dissolved oxygen, but it is more expensive.
(3) Carbon dioxide: It is easier to obtain, cheaper, and denser than nitrogen. There is no significant difference in curing behavior between carbon dioxide and nitrogen atmospheres; even as low as 1% oxygen content can significantly slow down the polymerization rate of the system. In a carbon dioxide atmosphere, increasing the temperature accelerates curing. However, in an air atmosphere, raising the temperature increases the diffusion rate of oxygen, thereby reducing the curing rate of the system.
(4) UV production lines protected by an inert atmosphere find applications in many fields, including furniture, PVC flooring, and silicone release coatings. In fact, due to the greater absorption and permeation of oxygen by silicone acrylate resins and oligomers, inert gas protection is a critical technology for achieving products such as UV-cured silicone acrylate-based release papers.
| Polymer | Permeability coefficient (×10⁻¹⁰ cm/s) | ||
| O 2 | N 2 | CO 2 | |
| PDMS | 605 | 300 | 3240 |
| PTFE | 4.9 | 1.33 | 12.7 |
| LDPE | 2.89 | 0.97 | 12.6 |
| PMMA | 0.154 | 8.18 | 3.10 |
| PETE | 0.03 | 0.001 | 0.029 |
| PVA | 0.00052 | 0.00045 | 0.0005 |
2. Physical barrier
(1) Sealing and isolating the system with a transparent liquid or solid—this method is not suitable for continuous coating lines at the industrial scale.
(2) Floating Wax Method
(3) Film-coating method
3. Light Intensity
(1) A simple way to reduce oxygen inhibition is to increase the light intensity, which promotes the formation of a higher concentration of free radicals from the initiator. These free radicals quickly react with dissolved oxygen, thereby reducing its concentration.
(2) When the oxygen concentration drops to approximately 4.2 × 10⁻⁶ mol/L, the chain propagation reaction becomes more competitive relative to the formation of peroxyl radicals.
(3) Excessively high light intensity may rapidly deplete active free radicals before chain growth is complete, causing the polymerization reaction to terminate abruptly.
4. Light source
(1) Continuous ultraviolet flash irradiation technology can generate brief but intense pulses of ultraviolet radiation, thereby producing free radicals at extremely high concentrations.
(2) Lasers can also be designed to emit high-intensity, narrow-bandwidth light sources that enable complete curing within just a few milliseconds. Due to their high cost and limited curing area, laser curing is used only in niche, specialized applications.
(3) The vacuum ultraviolet light emitted by excimer lamps (e.g., 172 and 222 nm) has very low penetration, allowing it to cure only ultra-thin coatings of 1–2 μm in thickness. At these wavelengths, curing does not require a photoinitiator, and the resulting concentration of free radicals is extremely low. When the reaction is carried out in air, significant ozone generation occurs.
3. Chemical inhibition of oxygen-induced polymerization suppression
1. Photoinitiator
(1) It is divided into two major categories: cleavage-type (I) and hydrogen-abstraction-type (II).
(2) Type I initiators absorb radiation and undergo bond cleavage from the excited triplet state to generate free radicals.

Cleavage type (I):




Hydrogen-abstraction type (II):

In Type II systems, the photosensitizer absorbs light to generate an excited-state triplet state, which triggers electron transfer in the co-catalyst, forming an excited-state complex. Subsequently, proton transfer occurs, yielding two free radicals: one is a carbonyl radical, and the other is a radical derived from the hydrogen donor.
The polymerization reaction is almost exclusively initiated by free radicals (D•) generated from hydrogen donors, whereas carbonyl radicals are constrained by steric hindrance and electron delocalization.
Type II systems are often considered to reduce oxygen inhibition in photopolymerization, which can be attributed to the presence of hydrogen donors (especially amines and thiols) that either lower the concentration of oxygen molecules or react with the peroxide radicals generated.
2. Inert molecules

The oxime ester (PDO) with good thermal stability can efficiently photolyze to generate free radicals and CO2.
Oxime esters have been successfully applied in color filters for liquid crystal displays (LCDs), allowing direct exposure through a mask in air without the need for a protective film.
The photoreactivity of oxime esters is lower than that of other photoinitiators, but they exhibit exceptional performance due to their ability to overcome oxygen inhibition.
A similar example is the derivative of N-phenylglycine.
3. Hydrogen donor

Alkyl peroxyl radicals do not readily react with acrylic monomers. A hydrogen donor (DH) provides a hydrogen atom, which can then be captured by the alkyl peroxyl radical to form a newly generated radical (D•), thereby reinitiating monomer polymerization—a chain-transfer mechanism.
(1) Amine

Please note: Amines exhibit significant dark reactions when used with acyl phosphine photoinitiators.
(2) Thiols


(3) Other reducing agents
a. Organoborane
A characteristic of borane radical initiators is that most of them require oxygen as a co-initiator; the main issue lies in the stability of boranes and their tendency to react prematurely.
However, after boranes are compounded with amines, both their storage stability and oxygen-inhibited polymerization effect are improved.

b. Organophosphines and phosphites
Aryl and alkyl phosphates can also be used to inhibit oxygen-induced polymerization, functioning in a manner similar to the oxidation by phosphine peroxyl radicals.
Trialkyl phosphates exhibit a significant amplification effect on the Type II photoinitiator system for thioxanthone, enabling complete curing even under low-energy air conditions.

4. Formula Improvement
(1) Reactive (methyl)acrylate
Based on the application of hydrogen-donating agents in inhibiting oxygen-induced polymerization, it is reasonable to consider using hydrogen-donating active monomers. Typically, the carbon atom adjacent to an electron-rich heteroatom—such as oxygen, sulfur, or nitrogen—can serve as the site for hydrogen abstraction, and this abstraction avoids chain transfer. The carbon radicals generated through hydrogen-abstraction chain transfer are consumed by oxidation reactions that utilize oxygen.


(2) High-functional/Hyperbranched Acrylates
The competitive reaction between high polymerization rate and free-radical oxidation is not the decisive factor determining whether highly functional monomers or resins can effectively inhibit oxygen-induced polymerization inhibition; rather, the formation of a unique polymer network may be the key factor.
(3) N-Vinylamide

N-Vinylpyrrolidone (NVP), whether in the presence or absence of oxygen, significantly enhances the copolymerization rate with acrylates.
(4) Donor/Acceptor Monomer

The combination of maleimide and vinyl ether represents a promising new system as an alternative to acrylic resins. However, several issues still remain, including storage stability, recrystallization of maleimide, and irritancy.
Share to:
Related News
The Printing Process (Part 2): Printing Methods
Printing methods can be classified according to the relative positions of image and non-image areas on the printing plate. The common printing techniques can be broadly divided into four major categories: letterpress printing, offset printing, gravure printing, and screen printing. It is essential to select the appropriate printing method based on the requirements of the printed material in order to achieve the desired results.
The Art of Printing (I): An Encyclopedia of Printing
Printing is a technology that involves transferring ink onto the surfaces of materials such as paper, textiles, plastics, and leather through processes including plate-making, inking, and applying pressure, thereby mass-replicating the content of original manuscripts—be it text, illustrations, photographs, or anti-counterfeiting elements.
Overview of Water-Based Coatings
Water-based coatings are heterogeneous systems formed by using water as the dispersion medium and resin as the dispersed phase.