Introduction to Wood UV Coatings and Their Applications


I. Introduction to the Classification of Wood Coatings

1. Classified by coating composition

(1) Nitrocellulose coatings (nitro lacquers/NC lacquers); (2) Unsaturated polyester coatings (PE lacquers); (3) Polyurethane coatings (PU lacquers); (4) Acid-cured coatings (AC lacquers); (5) Ultraviolet-curable coatings (UV lacquers); (6) Water-based coatings (Water).

2. Nitrocellulose coatings (nitro lacquers/NC lacquers)

Nitrocellulose lacquer: A coating whose primary film-forming substance is nitrocellulose and which dries through natural evaporation. This type of coating offers significant advantages when used for finishing export furniture products and is highly favored by foreign buyers from Europe and the U.S.;

The so-called American-style finish refers to a paint coating suitable for and popular among furniture designed for regions such as Europe and the United States. American-style finishes have a strong European and American flair. In China, NC paints are primarily used for export trade.

Advantages:

(1) Rapid drying: While conventional paints typically take 24 hours to dry, nitrocellulose lacquers can dry in just a little over ten minutes. This significantly reduces construction time and boosts work efficiency.

(2) Simple construction: Nitrocellulose coatings are single-component products; when preparing them, simply add an appropriate amount of thinner and you’re ready to spray.

(3) Stable gloss: Less affected by environmental factors.

Disadvantages:

(1) Insufficient film thickness: Due to the low solid content of nitrocellulose coatings, it is difficult to form a thick paint film.

(2) Insufficient hardness: The hardness of nitrocellulose coatings typically ranges around BH.

(3) The paint film surface is not resistant to solvents;

(4) Nitrocellulose lacquers contain large amounts of solvents and cause serious environmental pollution.

3. Unsaturated polyester coatings (PE paint)

Definition: The condensation product of polybasic acids and polyols is called a polyester; when the polyester contains unsaturated double bonds, it is referred to as an unsaturated polyester. Coatings whose primary film-forming substance is an unsaturated polyester are known as unsaturated polyester coatings (PE paints).

Film-forming principle: Unsaturated polyester mixed with a monomer (typically polyethylene) can form a film at room temperature in the presence of an initiator (peroxide) and an accelerator (organic cobalt salt).

Advantages:

(1) It has excellent hardness, reaching 3H or higher;

(2) The topcoat can achieve a very high gloss level;

(3) Excellent wear resistance, acid and alkali resistance, and heat resistance;

(4) The paint film is very thick and has excellent fullness.

Disadvantages:

(1) The operation is relatively complex: A curing effect can only be achieved by adding both an initiator and a promoter. The amounts of initiator and promoter to be added must vary depending on changes in temperature and humidity. The initiator and promoter must not be mixed into the paint at the same time; otherwise, this could easily lead to fire or explosion. There are strict requirements when preparing the paint.

(2) The prepared paint has a very short active life; it’s best to use the prepared paint within 25 minutes.

(3) Currently, the PE topcoat is available only in a glossy finish; matte finishes are not yet offered.

4. Polyurethane Coating (PU Paint)

Definition: Typically composed of two components—the isocyanate prepolymer and the hydroxyl-containing resin—commonly referred to as the curing agent component and the main agent component, respectively. This type of coating comes in many varieties and has a wide range of applications.

Advantages:

(1) It exhibits excellent performance in terms of fullness, hardness, toughness, and impact resistance.

(2) Good workmanship stability and high product reliability;

(3) It can be combined with other types of paints to achieve various visual effects, making it a paint with outstanding overall performance and the most widely used.

Disadvantages:

(1) Its workability is inferior to that of NC paint;

(2) Mixing paints with multiple components is inconvenient, and thick coatings are prone to bubble formation.

5. Acid-curing coatings (AC coatings)

Definition: This refers to the use of an acidic catalyst to accelerate the crosslinking and curing of amino resins and alkyd resins, allowing the coating to cure into a film at room temperature without baking.

Advantages:

(1) The paint film is hard and wear-resistant;

(2) The coating film exhibits excellent heat resistance, water resistance, and cold resistance.

(3) Good transparency;

(4) Good resistance to yellowing.

Disadvantages:

Because paints containing free formaldehyde can cause serious health harm to workers, the vast majority of companies have stopped using such products.

6. Water-borne coatings

Definition: A coating system in which water serves as the solvent, and the film-forming substance is primarily an acrylic emulsion or a polyurethane emulsion.

Advantages:

Easy to construct, highly efficient, non-toxic, non-irritating, environmentally friendly, and in line with modern aesthetic tastes; easy to apply and featuring excellent film flexibility.

Disadvantages:

The paint film is relatively thin and lacks fullness; its hardness is insufficient. At this stage, water-based paints still face limitations such as high costs and poor overall performance, resulting in low market acceptance.

7. Ultraviolet-curable coatings (UV paints)

Advantages:

(1) Green and environmentally friendly: Solid content 100%, no solvent volatilization;

(2) High efficiency: Easy to operate with machinery and cures instantly;

(3) Low cost: The cost is only two-thirds or one-half of that of PU;

(4) There are no time constraints on usage.

(5) Resource savings: Significant savings in manpower and space;

(6) Excellent performance: high hardness, good wear resistance, excellent transparency, and stable quality.

Disadvantages:

(1) The equipment is expensive;

(2) The product has a narrow scope of applicability and currently applies only to flat surfaces;

(3) It consumes a lot of energy—each complete production line requires at least 400 kilowatt-hours, while a single mercury lamp consumes about 10 kilowatt-hours per hour. Therefore, continuous production is essential.

(4) Adhesion is generally moderate; it’s particularly difficult to achieve good adhesion for dark-colored coatings.

(5) High technical requirements for construction personnel.

Simple differences between PU, PE, NC, WT, and UV

  Reaction mechanism Film-forming substance Solvent present or absent Film-forming time Film-forming promoting factors Difference
PU Addition polymerization Polyurethane There is 4h Temperature, humidity, ventilation Named after the film-forming substance
PE Polycondensation reaction Polyester There is 4h Temperature, humidity, ventilation Named after the film-forming substance
NC Volatile Film-Forming Nitrocellulose There is 2h Temperature, humidity, ventilation Named after the film-forming substance
WT Addition reaction Water-soluble modified resin There is 1h Temperature, humidity, ventilation By solvent type
UV Free-radical-initiated polymerization Acrylic resin and unsaturated resin None 3s-5s Ultraviolet light By film-forming method

Performance Comparison of Several Wood Coatings: NC, PE, PU, and UV

Performance NC PU PE UV
Coating dilution solid content 15-30% 30-45% Over 70% Over 70%
Drying time per cycle About 1 hour About 4 hours About 4 hours About 30 seconds
Available time Unlimited 4-8 hours Within 30 minutes Unlimited
Grindability Good Better Poorer Poor
Workability Very good Good Not good Very good
Paint odor Better General Poor Poor
Film fullness Poorer General Good Very good
Coating adhesion Good Very good Good Good
Single-coat application amount About 130 About 130 About 130 About 130
Coating hardness B-H HB-2H H-3H 2 hours or more
Solvent resistance Poor Best Good Good
Heat resistance Low Very high High High
Durability Poor Very good Good Good
Unit price of paint Low Middle and high Middle and high Very high

II. Composition of Wood UV Coatings

1. Industry Characteristics of Domestic Wood Coatings

(1) The production and coating technologies in the UV furniture coatings industry are already relatively mature.

(2) In UV wood coatings, floor coatings account for an absolute share of over 85%. This market has now reached saturation, and many companies have begun engaging in price wars.

2. Current Status of Domestic and International Brands

Development has been relatively rapid, and some enterprises have already achieved a certain scale of production. However, the product quality is not yet high, and there remains a noticeable gap compared to Europe, the U.S., and Japan.

Overseas: PPG, Jinfu, AkzoNobel, Valspar, Kunlun, and others;

Domestic: Xigui, Bangdeli, Jia Baoli, Zhan Chen, Yada, Longzhu, and others.

3. Composition of UV Coatings

(1) Monomer

Active diluent, which adjusts viscosity, participates in photocuring, and influences the curing rate and the performance of the coating film;

The main monomers used in wood coatings include TMPTA, TPGDA, and HDDA; others include HEMA, DPHA, EHA, and DPGDA.

(2) Oligomer

The main component of UV coatings determines the performance of the paint film after curing.

Epoxy and modified epoxy resins (B-102M, B-163, B-151), polyester resin (B-516 self-curing polyester), aromatic polyurethanes, aliphatic polyurethanes (B-675, B-305, B-268M), modified polyurethanes (B-6380NY), adhesion-promoting resins (high-acid-value polyesters), and pure acrylic resins (B-555), among others.

(3) Photoinitiator

An important component of light-curable coatings that plays a decisive role in the curing speed;

1173, 184, TPO, 819, BP, active amine, macromolecular initiator, BI-754.

(4) Colorant filler

Pigments: Fine, powdered colored substances that are uniformly dispersed in the coating’s base material. When applied to a substrate surface, they form a colored layer and exhibit a specific color (such as titanium dioxide, carbon black, and other pigments).

Dye: A finely powdered, colored substance that can dissolve in the base material of a coating to produce a transparent and vivid color without obscuring the substrate.

Pigments are used as colorants in colored coatings; dyes are used as colorants in transparent varnishes.

Fillers: Reduce costs, enhance the rheological and mechanical properties of coatings, have a refractive index close to that of resins and diluents, and exhibit no hiding power on substrates (talc, calcium carbonate, barium sulfate, kaolin, silica).

Various performance metrics Pigment (color paste) Dye (color concentrate)
State in the coating Dispersant Dissolver
Durability Non-fading (inorganic) Color-changing (organic)
Covering power There is None
Color bleeding (color migration) Not easy Easy
Fillability There is None

(5) Solvent

A substance that can dissolve other materials and form a homogeneous solution. Its function is to dissolve or disperse the film-forming component into a uniform and stable liquid dispersion system, facilitating the preparation of coatings, their application, film formation, and subsequent evaporation into the atmospheric environment.

Pine oil, alcohol, aromatic hydrocarbons (such as benzene, toluene, and xylene), alcohols (such as butanol), esters (such as butyl acetate), ethers (such as ethylene glycol ether), ketones (such as cyclohexanone), and others;

Solvents have a significant impact on the viscosity, gloss, leveling properties, wettability, and adhesion of coatings. Using the wrong solvent or a solvent that is incompatible with the coating can lead to cloudiness, precipitation, loss of gloss, or whitening of the coating.

(6) Additives

Although used in small amounts, it significantly improves a specific aspect of the coating or paint film’s performance.

Additives that improve the processing performance of coatings: such as defoamers, dispersants, and wetting agents;

Additives that improve the storage performance of coatings—such as anti-settling agents;

Additives that improve the application performance of coatings, such as anti-sagging agents and thixotropic agents;

Additives that improve the curing and film-forming performance of coatings, such as driers, curing accelerators, film-forming aids, and photoinitiators.

Additives that improve coating film performance: such as adhesion promoters, leveling agents, slip additives, and light stabilizers;

Additives that impart specific functions to coatings, such as flame retardants, antifouling agents, and antistatic agents.

III. Classification of UV Coatings for Wood Furniture

1. Classified by construction function

UV putty paint, UV primer, UV topcoat

2. By coating method

Roll coating, spray coating, dip coating, scrape coating, etc.

3. UV Putty Paint

For boards with poor surface smoothness, this product serves to fill small pores and minute imperfections in the substrate, sealing the substrate surface so that subsequent decorative coatings won't be absorbed, preventing an uneven appearance and providing a smooth finish.

UV putty has a fast curing rate, high viscosity (even paste-like), low cost, and good sandability.

In addition to the basic components, the formulation also contains a relatively high proportion of inorganic fillers, primarily to reduce costs. These inorganic fillers can enhance the hardness and sandability of the paint.

Resins: B-102M, B-516, BI-754.

4. UV Primer

Compared to putty, UV primer contains relatively fewer inorganic fillers and has a relatively lower viscosity, making it suitable for surfaces that are relatively smooth.

Categories: General Primer, Sanding Primer, Tinted Primer, Hardening Primer, High-Transparency Primer, Yellowing-Resistant Primer;

The purpose of sanding the primer and putty is to enhance the interlayer adhesion between the topcoat and the primer or putty.

Resins: B-102M, B-163, B-516, B-6315A, B-6380NY, BI-756.

5. UV topcoat

Primarily serves a decorative function; has low viscosity;

The difference between this product and primer and putty lies in the fact that it does not contain inorganic fillers in its composition.

Gloss: Glossiness greater than 95°;

Matte: matting powders, wax powders, matte resins, etc.;

Resins: B-102M, B-163, B-675, B-516, B-305, B-6315A, B-216, and a newly developed silicone resin.

IV. UV Coating Process for Wood Products

1. Roller coating

It can only be used for flat-surface coating and has advantages such as low cost, high efficiency, ease of continuous production, and zero pollution. Its disadvantages include the inability to coat three-dimensional workpieces and relatively high equipment investment.

2. Dip coating

This coating process is suitable for flat panels and offers advantages such as mechanized operation, high efficiency, low pollution, and excellent coating appearance. However, it has several drawbacks: it demands strict requirements for the construction environment, the process is difficult to control, and the cost is relatively high. Therefore, it is not well-suited for production involving multiple varieties in small batches.

3. Spraying

Suitable for dissimilar parts, high efficiency, high cost.

Roller coating is the most widely used coating method for panel furniture and paper products. It features simplicity, speed, and cost-effectiveness. Although roller coating produces less fullness in wood flooring coatings compared to spray coating, it imparts a more natural-looking surface. Moreover, in terms of paint formulation design, roller coating offers advantages over spray coating, giving it certain benefits over spray coating. Currently, this coating method is commonly adopted for wood flooring exported from China.

4. UV Roller Coating Machine

5. UV Coating Machine

6. UV curing machine

7. Sanding machine

8. Coating Process for Composite Wood Flooring

Standard process: four bottoms and two sides

Schematic diagram

9. Wood flooring primer production line

10. Wood flooring topcoat production line

11. Furniture Coating Process – Roller Coating

12. Furniture Coating Process – Spraying

V. Performance Indicators and Defect Analysis of Wood UV Coatings

1. Performance indicators of wood UV coatings

(1) Fineness: Topcoat ≤ 25 μm, Primer ≤ 50 μm;

(2) Curing speed: 0–15 m/min; the line speed is controlled by the slowest section.

(3) Adhesion ≤ Grade 1, grid test method;

(4) Hardness ≥ 2H;

(5) Water resistance of the composite layer: No bubbling, wrinkling, or peeling after 72 hours;

(6) Wear Resistance: Weight Loss Method, 750 g, 500 r, ≤ 0.03 g;

(7) Thermal Cycling: After 24 hours (-20℃—60℃; 4 hours) × 10;

(8) Viscosity: mPa/s, cup No. 4 ≤ 150 s;

(9) Coating amount: Roller coating: 5–40 g/m²; Dip coating: 80–130 g/m²; Spray coating: 110–250 g/m².

2. Performance Indicators and Defect Analysis of Wood UV Coatings

(1) Uneven gloss: The substrate deformation or issues with the roller bearings cause uneven paint application.

(2) Poor adhesion: caused by excessive moisture or oil content in the substrate, overapplication of a single coat, inadequate sanding between layers, or excessively high pigment and color paste content.

(3) UV coating fails to cure: The UV lamp’s lifespan is too short, the coating application amount is too low (oxygen inhibition), the substrate or paint color is too dark, or the paint itself contains insufficient photoinitiators.

(4) Roller Marks: The rubber roller is pressed too tightly, the rubber roller is deformed, the leveling time is insufficient, the conveyor belt speed is faster than the coating roller’s speed, or the coating amount is excessive.

(5) Poor scratch resistance: The surface finish is insufficient. To improve the surface smoothness, Jianfu Technology recommends applying two coats of topcoat at a total application rate of 20 g/m²—15 g for the first coat and 5 g for the second coat.

(6) Glossiness that is too high or too low: UV lamp energy, coating film thickness, curing speed of the paint, leveling time, and paint temperature.

(7) Oil buildup at the head and tail of the paint board: inconsistency between the conveyor belt speed and the roller speed, the height of the coating roller, and the coating amount.

VI. Cost Analysis of UV Coating for Wood Products

Although the unit price of UV coatings is currently higher than that of PU, PE, and NC coatings, due to their lower solid content compared to PU, PE, and NC coatings, they are typically applied by spray coating, resulting in higher paint consumption. In contrast, UV coatings have a high solid content and can be applied by roller coating, leading to lower paint consumption. Therefore, the overall coating cost of UV coatings is generally lower than that of PU, PE, and NC coatings, offering a clear cost advantage.

Cost accounting
(RMB/m²)
UV varnish PU paint PE paint NC paint
Primer 3.2-6 7.8–12 5.1–6.3 10.3–14.5
Topcoat 2.5-6 7-9.2 5.4–6.8 9.5–11.6
Total 5.7-12 14-21.2 10.5–13.1 19.8–26.1

Note: Comparison is made under the condition of equal film thickness, with coating applied for a fully enclosed effect.

Share to:

Related News


Principle and Application of Polymerization Inhibitors

In unsaturated compound systems, polymerization inhibitors can preferentially react with free radicals in the system, forming non-radical species or generating free radicals with low reactivity that are insufficient to initiate further polymerization. This effectively halts the chain-growth polymerization process involving free radicals, bringing significant benefits to the stability, storage, and transportation of resins.


Crosslinking Modification of Waterborne Polyurethane

The molecular chains of waterborne polyurethane resins typically have a linear structure or a small number of branched structures, and films without crosslinking exhibit relatively low strength. To enhance the water resistance, chemical resistance, high-temperature resistance, and mechanical properties of their cured films, it is necessary—during resin synthesis—to appropriately increase the degree of crosslinking, introduce certain crosslinkable functional groups, or add crosslinking agents, thereby ensuring sufficient crosslinking during film formation and creating either an interpenetrating network structure or a polymerized crosslinked system that meets various application requirements.