Tel
Tel
+8618142863185
Follow us
Official Accounts
Official Accounts
- Top
Analysis of the Risk of UV Adhesive Performance Degradation (Part 2)
Release time:
2025-08-13 16:38
In industries such as healthcare and electronics, where material performance is subject to stringent requirements, UV adhesives have found widespread use thanks to their rapid curing speed and excellent bonding strength. However, UV adhesives containing plasticizers face a serious issue—plasticizer migration—at elevated temperatures, which poses significant potential risks to product performance and quality.
I. The Intrinsic Mechanism of Plasticizer Migration
Plasticizers, as key additives that enhance the flexibility and moldability of adhesives, possess relatively small molecular structures. Under normal environmental conditions, they remain stably embedded within the adhesive layer, effectively fulfilling their intended function. However, when exposed to high temperatures, increased thermal motion endows plasticizer molecules with sufficient energy to overcome the binding forces of the adhesive matrix. Consequently, these small molecules begin to migrate from the interior of the adhesive layer toward its exterior, gradually detaching from their original positions. This migration does not occur instantaneously; rather, it progresses continuously over time as the duration of elevated temperature increases, constituting a gradual and sustained process.
II. Significant Deterioration of the Adhesive Layer’s Physical Properties
Taking the bonding of PVC catheters in medical‑device manufacturing as an example, the migration of plasticizers has a pronounced impact on the physical properties of the adhesive layer. After PVC catheters are stored for a period under relatively high‑temperature conditions, plasticizers leach out of the adhesive layer, leading to a substantial reduction in its hardness. The adhesive layer, which originally possessed adequate strength and toughness, becomes soft and loses its structural support. Consequently, the bond at the catheter’s attachment point is significantly weakened, rendering it extremely fragile. During routine use, even minor external forces can cause the bonded joint to loosen or detach entirely. For medical catheters—products that demand precise handling and high reliability—the failure of the bond can severely compromise their proper function, potentially disrupting clinical procedures and imposing considerable inconvenience on patients.
III. Potential Threats to Biosafety
In addition to affecting the physical properties of the adhesive layer, plasticizer migration also poses significant biosecurity concerns. In the medical field, product biocompatibility is a critical consideration. Once migrated plasticizers come into contact with living organisms, they can trigger a range of adverse reactions. Biocompatibility testing has shown that certain plasticizers exhibit cytotoxicity, disrupting normal cellular functions and leading to cell death or mutation. When these harmful plasticizers migrate to the catheter surface and interact with patient tissues or bodily fluids, they may pose potential risks to patient health. For example, they could provoke local inflammatory responses, allergic reactions, or even exert long-term detrimental effects on the patient’s immune system. Such latent biosecurity threats not only compromise patients’ physical well‑being but may also give rise to serious medical disputes.
IV. Reputational and Legal Risks Faced by Enterprises
Product performance degradation and biosafety concerns arising from plasticizer migration pose multifaceted risks to companies. From a reputational standpoint, any product quality issues or patient health incidents attributable to plasticizer migration can severely damage a company’s brand image. In today’s fast‑paced information environment, negative news can quickly spread throughout the industry and among consumers, eroding trust in the company’s products and leading to a decline in market share.
V. Conclusion
The migration of plasticizers from UV‑curable adhesives in high‑temperature environments can lead to a cascade of serious consequences, including degradation of the adhesive layer’s physical properties, threats to biocompatibility, and risks to corporate reputation and legal compliance. In applications across relevant industries, it is essential to fully recognize the gravity of this issue and strengthen monitoring and evaluation of product performance to ensure both quality and safety.
Disclaimer: The above content has been compiled from publicly available sources and is provided for reference only. If any infringement occurs, please contact us, and we will address it promptly.
| Bossin Related Product Recommendations – UV Adhesives | ||
| Electronic structural adhesive | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| B-151 | Modified epoxy acrylate | Low halogen, yellowing-resistant, excellent plating performance, and strong adhesion. |
| B-186 | Modified epoxy acrylate | Boil-resistant, excellent adhesion, high-temperature resistant, chemically resistant |
| B-2111D | Aliphatic polyurethane acrylate | Excellent adhesion, high elongation, and resistance to thermal shock. |
| B-2116 | Aliphatic polyurethane acrylate | Excellent adhesion, good flexibility, acid and alkali resistance, and excellent tensile strength. |
| B-215 | Aliphatic polyurethane acrylate | Good adhesion, excellent flexibility, water resistance, and acid resistance. |
| B-2622 | Polyurethane acrylate | Small shrinkage, excellent adhesion, good elongation, and excellent transparency. |
| B-295A | Aliphatic polyurethane acrylate | Fast curing, high hardness, resistant to boiling water and alkali. |
| Glass bonding | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| B-151 | Modified epoxy acrylate | Low halogen, yellowing-resistant, excellent plating performance, and strong adhesion. |
| B-186 | Modified epoxy acrylate | Boil-resistant, excellent adhesion, high-temperature resistant, chemically resistant |
| B-2058P-2 | Aliphatic polyurethane acrylate | Excellent adhesion, resistant to strong acids and strong alkalis, and low curing shrinkage. |
| B-2111D | Aliphatic polyurethane acrylate | Excellent adhesion, high elongation, and resistance to thermal shock. |
| B-211A | Aliphatic polyurethane acrylate | Good adhesion, excellent flexibility, and water resistance. |
| B-215 | Aliphatic polyurethane acrylate | Good adhesion, excellent flexibility, water resistance, and acid resistance. |
| B-295A | Aliphatic polyurethane acrylate | Fast curing, high hardness, resistant to boiling water and alkali. |
| Plastic bonding | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| B-2111D | Aliphatic polyurethane acrylate | Excellent adhesion, high elongation, and resistance to thermal shock. |
| B-2116 | Aliphatic polyurethane acrylate | Excellent adhesion, good flexibility, acid and alkali resistance, and excellent tensile strength. |
| B-215 | Aliphatic polyurethane acrylate | Good adhesion, excellent flexibility, water resistance, and acid resistance. |
| B-2621 | Aliphatic polyurethane acrylate | Excellent adhesion, resistant to strong acids and strong alkalis, and low curing shrinkage. |
| B-2622 | Polyurethane acrylate | Small shrinkage, excellent adhesion, good elongation, and excellent transparency. |
| Glass bonding to metal | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| B-151 | Modified epoxy acrylate | Low halogen, yellowing-resistant, excellent plating performance, and strong adhesion. |
| B-186 | Modified epoxy acrylate | Boil-resistant, excellent adhesion, high-temperature resistant, chemically resistant |
| B-2058P-2 | Aliphatic polyurethane acrylate | Excellent adhesion, resistant to strong acids and strong alkalis, and low curing shrinkage. |
| B-211A | Aliphatic polyurethane acrylate | Good adhesion, excellent flexibility, and water resistance. |
| B-215 | Aliphatic polyurethane acrylate | Good adhesion, excellent flexibility, water resistance, and acid resistance. |
| B-295A | Aliphatic polyurethane acrylate | Fast curing, high hardness, resistant to boiling water and alkali. |
| Solder Joint Protective Adhesive | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| B-151 | Modified epoxy acrylate | Low halogen, yellowing-resistant, excellent plating performance, and strong adhesion. |
| B-151DT | Modified epoxy acrylate | Yellowing resistance, excellent flexibility, good plating performance, and strong adhesion. |
| B-163 | Modified epoxy acrylate | Good flexibility, excellent pigment wetting, and strong adhesion. |
| B-165 | Modified epoxy acrylate | Good flexibility and strong adhesion |
| B-186 | Modified epoxy acrylate | Boil-resistant, excellent adhesion, high-temperature resistant, chemically resistant |
| B-215 | Aliphatic polyurethane acrylate | Good adhesion, excellent flexibility, water resistance, and acid resistance. |
| B-221 | Aliphatic polyurethane acrylate | Fast curing, resistant to boiling water |
| B-296 | Aliphatic polyurethane acrylate | Fast curing, chemical resistance, yellowing resistance, impact resistance |
| Liquid optical adhesive | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| B-2111D | Aliphatic polyurethane acrylate | Excellent adhesion, high elongation, and resistance to thermal shock. |
| B-2116 | Aliphatic polyurethane acrylate | Excellent adhesion, good flexibility, acid and alkali resistance, and excellent tensile strength. |
| B-215 | Aliphatic polyurethane acrylate | Good adhesion, excellent flexibility, water resistance, and acid resistance. |
| B-2621 | Aliphatic polyurethane acrylate | Excellent adhesion, resistant to strong acids and strong alkalis, and low curing shrinkage. |
| Crystal epoxy resin | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| B-276H | Aliphatic polyurethane acrylate | High hardness, fast curing, excellent toughness, and low yellowing. |
| B-286 | Aliphatic polyurethane acrylate | Low heat generation, excellent toughness, wear resistance, and impact resistance. |
| B-296 | Aliphatic polyurethane acrylate | Fast curing, chemical resistance, yellowing resistance, impact resistance |
| B-296M | Polyurethane acrylate | Fast curing, resistant to polar solvents, yellowing-resistant, and impact-resistant. |
| Three-proof adhesive | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| B-02 | Phosphate ester acrylate | Enhance adhesion to substrates such as metal, glass, and plastic. |
| B-404 | Aliphatic polyurethane acrylate | Excellent flexibility and moisture stability |
| B-404C | Aliphatic polyurethane acrylate | Excellent flexibility and moisture stability |
| B-405 | Aliphatic polyurethane acrylate | Excellent adhesion and superior moisture stability. |
| B-405H | Aliphatic polyurethane acrylate | Excellent adhesion and superior moisture stability. |
| B-549 | Polyester acrylate | Low viscosity, adhesion, and weather resistance |
| LED bead protective adhesive | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| B-113 | Bisphenol A epoxy acrylate | High hardness, high gloss, high fullness, containing 20% TPGDA. |
| B-151 | Modified epoxy acrylate | Low halogen, yellowing-resistant, excellent plating performance, and strong adhesion. |
| B-160D | Modified epoxy acrylate | Good flexibility, yellowing resistance, and excellent adhesion. |
| B-166A | Modified epoxy acrylate | Good flexibility and strong adhesion |
| B-166A-85 | Modified epoxy acrylate | Good flexibility, excellent adhesion, contains 15% HEMA. |
| B-166A-85P | Modified epoxy acrylate | Good flexibility, excellent adhesion, contains 15% HEMA. |
| B-186 | Modified epoxy acrylate | Boil-resistant, excellent adhesion, high-temperature resistant, chemically resistant |
| High-temperature resistant | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| B-186 | Modified epoxy acrylate | Boil-resistant, excellent adhesion, high-temperature resistant, chemically resistant |
| B-191A | Phenolic epoxy acrylate | Fast curing and excellent heat resistance |
| B-548 | Polyester acrylate | Withstands high temperatures of 250–280°C. |
| B-919B | Aliphatic polyurethane acrylate | Fast curing, high hardness, excellent toughness, and outstanding chemical and wear resistance. |
| Anti-spy adhesive | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| B-251 | Aromatic polyurethane acrylate | Fast curing, excellent flexibility, and good wetting of black ink pigments. |
| B-254 | Aliphatic polyurethane acrylate | Flexibility, pigment wettability, and double 85 resistance |
| Odor-Neutralizing UV Gel | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| B-2621 | Aliphatic polyurethane acrylate | Excellent adhesion, resistant to strong acids and strong alkalis, and low curing shrinkage. |
| Peelable adhesive | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| B-368 | Aliphatic polyurethane acrylate | Good toughness, excellent leveling, excellent bend resistance, and excellent heat resistance. |
| Water and oxygen barrier | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| B-291 | Aliphatic polyurethane acrylate | Low shrinkage, moderate softness and toughness, excellent chemical resistance, and superior water and oxygen barrier properties. |
| Monomer Recommendation | ||
| Product Model/English Abbreviation | Product Name/Product Type | Product Features |
| BM1105 (OPPEA) | 邻-Phenylphenoxyethyl acrylate | Low shrinkage, excellent adhesion, low volatility, high refractive index |
| BM1210 (PHEA) | 2-Phenoxyethyl acrylate | Low shrinkage, heat resistance, excellent adhesion, high refractive index |
| BM1211 (HPMA) | Hydroxypropyl methacrylate | HEMA-free, high strength, low irritation, and high adhesion |
| BM2101M (10EO-BPADMA) | Bisphenol A dimethacrylate ethoxylate | Low irritation, flexibility, excellent strength, and heat resistance |
| BM2224 (EO-HDDA) | Ethoxylation of 1,6-hexanediol diacrylate | It exhibits excellent adhesion to plastics, good dilutability, and low volatility. |
Share to:
Related News
Analysis of the Risk of UV Adhesive Performance Degradation (Part 1)
Among numerous industrial materials, UV adhesives have found widespread application in fields such as electronics, optics, and advertising, thanks to their rapid curing and high bonding strength. However, in outdoor applications exposed to ultraviolet radiation over extended periods, UV adhesives face significant performance degradation, with yellowing being particularly pronounced, thereby posing substantial risks to the quality and service life of related products.
The Impact of Humid Environments on UV Optical Adhesives (Part 5)
In the medical device industry, the performance and safety of every component directly impact patient health and well‑being, leaving no room for compromise. UV‑curable optical adhesives, with their rapid curing and substantial bond strength, have found widespread use in medical device manufacturing—particularly in the assembly of precision instruments such as endoscopes. However, humid environments pose significant challenges to these adhesives, severely compromising both the performance and biocompatibility of medical devices.
The Impact of Humid Environments on UV Optical Adhesives (Part 4)
In the field of composite material bonding, UV‑curable optical adhesives are widely used across numerous industries, including aerospace and automotive manufacturing, thanks to their rapid curing and high bond strength. However, when composite bonded joints are exposed to humid environments, the performance of these adhesives faces significant challenges; in particular, internal stresses arising from size effects emerge as a critical factor leading to adhesive failure.