2EO-HDDA and HDDA Performance Comparison Test Report


Abstract: HDDA, chemically known as 1,6-hexanediol diacrylate, features low viscosity, strong diluting capacity, and excellent adhesion to plastic substrates; however, it exhibits relatively high skin irritancy. The Bosheng New Materials Technology Center has developed an ethoxylated version of HDDA—2EO-HDDA. Let’s take a look at how these two compounds compare.

I. Comparison of Basic Parameters

1. Molecular structure

HDDA, CAS No.: 13048-33-4

2EO-HDDA, CAS NO.: 84170-27-4

2. Basic Parameters

Note:

*Solid Content Determination by Drying: Fold aluminum foil into a 10×10 cm square dish. Weigh out 4 g of the sample and spread it evenly onto the square dish. Place the dish in an oven set at 110℃ and dry for 3 hours. Weigh the sample before and after drying, and calculate the solid content based on the weight of the non-volatile components.

* Dilution Capability Test: B-100M: Monomer = 1:1. After thorough mixing and stirring, allow the sample to stand undisturbed. Use a rotational viscometer to measure the viscosity of the sample at 30°C.

Summary: 2EO-HDDA has higher viscosity, a roughly 10% increase in solid content after baking, reduced volatility, but slightly diminished diluting ability. Its odor and skin irritancy are significantly lower than those of HDDA; however, the glossiness of the cured film is reduced.

II. Applications of Skin-Feel Coatings

1. Skin-feel curing process

Pre-cure with 395nm LED → Surface cure and wrinkling occur under a 254nm UV lamp, resulting in a matte finish → Thoroughly cure with high-energy UV mercury lamps.

2. Skin-feel coating formulation

Experimental Procedure Description: First, prepare the main component of the sample at a ratio of 13/5 (main component/monomer) and mix thoroughly until homogeneous. Apply the mixture onto a glass surface at a thickness of 25 μm, and cure it sequentially using LED 395 nm, 254 nm, and a high-pressure mercury lamp. The experiment will examine the time required to achieve a matte surface, the degree of mattness, and the yellowing resistance performance when using different monomers.

Results of the sensory feel response speed test for EO-modified monomers:

Summary: The shorter the time required for the coating to form a matte surface, the stronger the responsiveness to skin feel. The short response time of EO-modified monomers indicates that ethoxylated monomers have a promoting effect on the wrinkling response of skin feel.

III. Summary

2EO-HDDA compared to HDDA.

Advantages:

1. The solid content after baking increases by about 10%, and the odor and skin irritancy are significantly reduced.

2. The ablation capability on the substrate is reduced, which is advantageous for substrates that are not resistant to ablation.

3. It has low glossiness, and in terms of skin feel response, 2EO-HDDA exhibits higher responsiveness than HDDA.

Disadvantages:

1. As the molecular weight increases, the viscosity of 2EO-HDDA is slightly higher than that of HDDA, and its dilution capacity at the same proportion decreases.

2. The ablation capability on the substrate is weakened, and the adhesion to the substrate surface becomes weaker;

3. The surface drying hardness and crosslinking density differ from those of HDDA, requiring adjustments to the formulation; however, the differences are not significant.

As one of the four conventional monomers, HDDA boasts excellent diluting properties and good adhesion. However, it exhibits significant irritancy and poses substantial health risks to construction workers. Adopting EO-modified HDDA to reduce its irritancy is not only feasible but also offers additional performance advantages. We recommend that downstream customers actively expand its application scope, leveraging its strengths while addressing its limitations.

Note: The 2EO-HDDA is currently in the laboratory development stage. We can provide a small number of samples for testing. If you require samples, please contact the relevant business colleagues.

Share to:

Related News


Development of a UV Glass Protective Ink for Ultra-Resistant Cutting Fluids

This paper addresses the issue of easy damage to the surface of optical glass displays during processing and fabrication. We have researched and developed a UV glass protective ink that exhibits exceptional resistance to cutting fluids. Furthermore, we investigated the effects of varying ratios of photoinitiators, UV resin formulations, active diluent monomer ratios, and different adhesion promoters on the ink’s surface drying time, adhesion strength, resistance to cutting fluids, and alkali-removal performance.


Application of UV Resins in Wood and Building Material Coatings

In the field of wood coatings, the application of UV resins has already been practically validated. For example, researchers have synthesized a water-resistant UV resin specifically designed for use as a UV primer followed by a water-based topcoat in wood finishes. This resin boasts several advantageous properties, including rapid photocuring speed, high hardness, excellent flexibility, outstanding interlayer adhesion, and superior water resistance. These characteristics indicate that UV resins hold great potential for application in wood coatings.


A Comprehensive Performance Comparison of Silicone Photocurable Resins

This article presents performance evaluation tests on four silicone UV resins developed by Boxing Company. To help everyone clearly and concisely understand the performance characteristics of these four resins, the tests focus on a parallel comparison of the products’ most fundamental physical properties and performance attributes. We hope these results will be helpful to our customers in selecting the right products and formulating their applications.