Curing Mechanism of Epoxy Resins and Common Curing Agents


I. Reaction Mechanism

Acid-catalyzed reaction mechanism catalyst: proton donor; the order of promotion is: acid > phenol > water > alcohol.

II. Classification of Hardeners

1. Reactive curing agent

(1) It can undergo addition reactions with EP molecules and, through step-growth polymerization, crosslink to form a three-dimensional network structure.

(2) These generally contain active hydrogen atoms and are accompanied by hydrogen atom transfer during the reaction, such as polyfunctional primary amines, polyfunctional carboxylic acids, polyfunctional thiols, and polyfunctional phenols.

2. Catalytic curing agent

The epoxy groups cure via either cationic or anionic polymerization mechanisms, using agents such as tertiary amines, imidazoles, and boron trifluoride complexes.

III. Common Curing Agents

(1) Fatty amine curing agent; (2) Aromatic polyamines; (3) Modified polyamines; (4) Polythiols; (5) Anhydride curing agents.

1. Fatty amine curing agent

Characteristics of fatty amine curing:

(1) High activity and can cure at room temperature;

(2) The reaction is highly exothermic and has a short pot life;

(3) Generally requires post-curing: 7 days at room temperature, followed by 2 hours at 80-100℃.

(4) The cured material has a low thermal deformation temperature, typically between 80-90℃;

(5) The cured material has high brittleness;

(6) Highly volatile and toxic.

2. Aromatic polyamines

Characteristics of aromatic polyamines:

(1) The cured product exhibits excellent heat resistance, chemical resistance, and mechanical strength, all of which are superior to those of aliphatic polyamines.

(2) Low activity; mostly cured by heating.

(3) The nitrogen atom experiences reduced electron cloud density and diminished basicity due to the benzene ring, as well as steric hindrance effects from the benzene ring.

(4) Mostly solid, with high melting points and poor processability;

(5) Liquefaction, eutectic mixture formation, and addition of polyamines to monoglycidyl ethers.

3. Modified Polyamine

(1) Epoxide Addition:

The molecular weight of the adduct increases, its boiling point and viscosity rise, its volatility and toxicity decrease, and its original brittleness is improved.

(2) Michael Addition:

a. Acrylonitrile and polyamines;

b. The active hydrogen of an amine can rapidly add to α,β-unsaturated bonds;

c. Nitrile ethylates reduce activity and significantly improve compatibility with EP.

(3) Mannich Reaction:

The Mannich reaction is a three-molecule condensation involving a polyamine, formaldehyde, and phenol.

a. The product can cure EP at low temperatures, in humid conditions, and underwater.

b. Typical product T-31: diethylenetriamine + formaldehyde + phenol;

c. Adaptable for civil engineering applications involving materials such as concrete, steel, and tiles;

d. Rapid repair and reinforcement of bonding.

(4) Thiourea-polyamine condensation:

a. Thiourea condenses with aliphatic polyamines upon heating to 100℃, releasing ammonia gas.

b. Can cure EP at extremely low temperatures (below 0℃).

(5) Polyamidation:

a. 9,11-oleic acid dimerization reaction with 9,12-oleic acid;

b. Then, two molecules undergo an amidation reaction with DETA (diethylenetriamine), resulting in a compound with very low volatility and toxicity.

c. Good compatibility with EP; no strict stoichiometric requirements;

d. The cured product exhibits excellent toughening effects;

e. Low exothermic effect, long pot life, and relatively low heat resistance of the cured product; HDT is around 60℃.

4. Polythiol

(1) Similar to a hydroxyl group;

(2) Polythiol compounds (liquid polydisulfide rubber) are typical polyfunctional thiols. When used alone, they exhibit very low reactivity and undergo virtually no reaction at room temperature—reaction is extremely slow or nearly nonexistent.

(3) Under the action of an appropriate catalyst, the curing reaction proceeds at a rate several times faster than that of polyamines.

(4) Low-temperature curing is more pronounced.

5. Anhydride curing agents

(1) The reaction rate is very slow and does not produce highly cross-linked products; therefore, it is generally not used as a curing agent.

(2) Low volatility, low toxicity, and low irritation;

(3) Slow reaction rate, low heat release, and long pot life;

(4) Low shrinkage and high heat resistance of the cured product;

(5) The cured product has high mechanical strength and excellent electrical performance;

(6) Requires heating for curing, with a long curing time;

(7) EP commonly used curing agents, second only to polyamines.

Main acid anhydride:

(1) Maleic anhydride > Phthalic anhydride > Tetrahydrophthalic anhydride > Methyltetrahydrophthalic anhydride;

(2) Hexahydrophthalic anhydride > Methylhexahydrophthalic anhydride;

(3) Methyl naphthalic anhydride;

(4) Benzene tetracarboxylic dianhydride;

(5) Modified anhydride;

(6) In an acid anhydride molecule, the presence of electron-withdrawing substituents enhances its reactivity.

4. Cationic/Anionic Catalysts

(1) The catalyst only plays a catalytic role and does not participate in the crosslinking itself.

(2) The dosage should primarily be based on experimental values;

(3) Catalytic ring-opening of epoxides leads to chain growth.

1. Common anionic catalysts

(1) Tertiary amine class

Using DMP-10 (dimethylaminophenol) and DMP-30, the phenolic hydroxyl groups significantly accelerate the resin curing rate, resulting in high heat release and a short pot life. EP exhibits rapid curing (24 hours/25℃).

(2) Imidazole class

It makes extensive use of liquid 2-ethyl-4-methylimidazole (with secondary amine active hydrogen and tertiary amine), offering a long pot life (8–10 hours), moderate-temperature curing, high thermal distortion temperature, and comparable heat resistance (100℃) to that of aromatic amines—making it a cationic curing agent, specifically a Lewis acid.

Chain termination occurs via ion-pair recombination.

2. Common Cationic Catalysts

(1) Lewis acids—such as BF3, SnCl4, and AlCl3—are electron acceptors;

(2) BF3 is the most widely used and is highly corrosive with very high reactivity. It typically forms complexes with amines or ethers—for example, the boron trifluoride-ethylenediamine complex, BF3:400—which is a crystalline substance melting at 87°C, stable at room temperature, and decomposing at 90°C, with its reactivity increasing after decomposition.

V. The Three Stages of Epoxy Resin Curing

(1) Liquid—Application Time: The resin/curing agent mixture remains liquid and is suitable for application;

(2) Gelation—Initiation of Curing: The mixture begins to enter the curing phase (also known as the maturation stage), during which it starts to gel or “suddenly transform” into a soft gel-like substance. At this stage, curing is only partial; the newly applied epoxy resin can still chemically bond with it. Therefore, the untreated surface remains capable of being bonded or reacted with.

(3) Solidification—Final Curing: The epoxy mixture enters the solid phase, at which point it can be sanded and shaped. It is left to cure further at room temperature for several hours.

6. Curing Temperature

(1) Low-temperature curing agents have a curing temperature below room temperature: modified amines, polythiol types, and polyisocyanate types;

(2) Room-temperature curing agents have a curing temperature ranging from room temperature to 50°C: aliphatic polyamines, cycloaliphatic polyamines, low-molecular-weight polyamides, and modified aromatic amines;

(3) The medium-temperature curing agent operates at 50–100°C: including certain alicyclic polyamines, tertiary amines, imidazoles, and boron trifluoride complexes;

(4) High-temperature curing agents have a curing temperature above 100℃: aromatic polyamines, anhydrides, resol phenolic resins, amino resins, dicyandiamide, and hydrazides, among others.

7. Properties of the Solidified Material

(1) For addition-polymerization curing agents, the curing temperature and heat resistance increase in the following order: aliphatic polyamines < alicyclic polyamines < aromatic polyamines ≈ phenolic resins < anhydrides; whereas the heat resistance of catalytic polyaddition curing agents generally falls at the level of aromatic polyamines.

(2) Hue: (Excellent) Aliphatic cyclic → Aliphatic → Amide → Aromatic amine (Poor);

(3) Degree of saturation: (low) aliphatic cyclic → aliphatic → aromatic → amide (high);

(4) Applicable period: (long) aromatic → amide → alicyclic → aliphatic (short);

(5) Curing speed: (fast) aliphatic → alicyclic → amide → aromatic (slow);

(6) Irritancy: (Strong) Aliphatic → Aromatic → Cycloaliphatic → Amide (Weak);

(7) Glossiness: (Excellent) Aromatic → Cycloaliphatic → Polyamide—Aliphatic amine (Poor);

(8) Flexibility: (soft) polyamide → aliphatic → alicyclic → aromatic (rigid);

(9) Adhesion: (Excellent) Polyamide → Alicyclic → Aliphatic → Aromatic (Good);

(10) Acid Resistance: (Excellent) Aromatic → Cycloaliphatic → Aliphatic → Polyamide (Poor);

(11) Water Resistance: (Excellent) Polyamide → Aliphatic Amine → Aromatic Amines → Aromatic Amines (Good).

Share to:

Related News


Introduction to Polymerization Methods

In the industrial production of polymer compounds, the same polymer can be produced using several different polymerization methods. Among methods that yield products with identical performance, the one offering superior product quality, lower equipment investment, and reduced production costs will be developed. Other methods, by contrast, will gradually be phased out. The choice of polymerization method depends on the properties of the polymer.


A Brief Discussion on Dual-Cure Systems

Since the curing process of UV-curable systems is initiated by light, UV-curable systems also have the following drawbacks: limited curing depth; difficulty in application to colored systems and opaque materials; and inability to cure objects with excessively complex shapes. To address these limitations, dual UV-curing systems have been developed, which combine UV curing with other curing methods. In such systems, the crosslinking or polymerization reaction is accomplished through two independent stages, each operating on a different reaction principle. UV light is used to rapidly set the system or achieve “surface dryness,” while a dark reaction ensures that the “shadowed” areas or inner layers are fully cured, reaching “full dryness.”


Introduction to the UV-CIPP (Ultraviolet Light-Cured In-Place Pipe Repair) Process

After years of operation, various pipelines inevitably suffer from damage and leaks due to factors such as corrosion and poor operational management, leading to significant economic losses. However, replacing the entire pipeline with new ones would not only involve an enormous amount of work but also be costly and time-consuming. Consequently, how to restore pipeline safety efficiently, economically, and quickly has attracted great attention both domestically and internationally. Therefore, research into pipeline repair technologies is of paramount importance.