Tel
Tel
+8618142863185
Follow us
Official Accounts
Official Accounts
- Top
Introduction to Polymerization Methods
Release time:
2016-08-26 10:53
I. Polymerization Methods for Polymers
1. By aggregation mechanism
(1) Stepwise Polymerization: Polymerization proceeds slowly and stepwise, with each step having roughly the same reaction rate and activation energy.
Condensation polymerization → Polyaddition → Ring-opening polymerization
(2) Chain Polymerization: Polymerization begins with active species and consists of elementary reactions such as chain initiation, chain propagation, and chain termination, which differ significantly in their rates and activation energies.
Free-radical polymerization → Ionic polymerization (anionic/cationic) → Coordination polymerization
2. Step-growth polymerization
(1) Polycondensation
a. Functional monomers are repeatedly condensed to form polymers;
b. Small-molecule byproducts are generated;
c. Such as the synthesis of polyester, polycarbonate, and phenolic resin, etc.
(2) Addition Polymerization
a. “Polyaddition”: Polymers are formed by the mutual addition of functional groups between monomer molecules;
b. No small-molecule byproducts are precipitated;
c. Such as polyurethane and polyurea synthesis, etc.
(3) Open-loop polymerization
a. The cyclic monomer’s sigma bond breaks, leading to the formation of a linear polymer;
b. No small-molecule byproducts are generated;
c. Such as polyoxyethylene and polycaprolactam (P-6).
3. Chain Polymerization
(1) Free-radical polymerization
a. The main types are bulk polymerization, solution polymerization, suspension polymerization, and emulsion polymerization.
b. The active species are free radicals;
c. Such as most olefin monomers and polyacrylates, etc.
(2) Ionic Polymerization
Including anionic and cationic polymerization.
(3) Other polymers
Such as coordination polymerization, living radical polymerization, and partial ring-opening polymerization, among others.
II. Comparison of Free-Radical Polymerization Methods

III. Characteristics of Four Types of Free-Radical Polymerization Methods
| Aggregation method | Bulk polymerization | Solution Polymerization | Suspension polymerization | Emulsion polymerization |
| Recipe | Monomer Initiator |
Monomer Initiator Solvent or water |
Monomer Initiator Water, dispersant |
Monomer Water-soluble initiator Water, emulsifier |
| Gathering place | Within the body | In solution | Inside a single droplet | Inside micelles and latex particles |
| Polymerization mechanism | Following the general rules of free-radical polymerization, factors that increase the reaction rate often lead to a decrease in molecular weight. | Can simultaneously increase both the rate and molecular weight. | ||
| Production characteristics | Difficult to dissipate heat, but self-acceleration is significant. Can be made into sheets. | Easy to dissipate heat, with a stable reaction and products that can be used directly. | Easy to dissipate heat, but the product requires post-processing, adding extra steps. | Easy to dissipate heat; when the product is in solid form, post-processing is required, but it can also be used directly. |
| Product Features | High purity, broad molecular weight distribution. | Low purity and molecular weight. | Relatively pure, but contains a dispersant. | Contains a small amount of emulsifier. |
| Operation method | Intermittent, continuous | Intermittent, continuous | Intermittent | Intermittent, continuous |
| Production instance | Acrylic glass Polystyrene Polyethylene |
Acrylate Acrylonitrile, polyacrylamide Vinyl acetate |
Polyvinyl chloride Styrene |
Styrene-butadiene rubber Acrylate class |
IV. Homogeneous and Heterogeneous Classification
| Single-component single-phase system | Aggregation method | Polymer-single-monomer-solvent system | |
| Homogeneous polymerization | Precipitation polymerization | ||
| Homogeneous system | Bulk polymerization (gas, liquid, and solid phases) | High-pressure polymerization of ethylene Styrene Acrylate |
Vinyl chloride Acrylonitrile Acrylamide |
| Solution Polymerization | Styrene—Benzene Acrylic monohydrate Acrylonitrile-dimethylformamide |
Vinyl chloride-methanol Acrylic one-hexane Acrylonitrile monohydrate |
|
| Heterogeneous system | Suspension polymerization | Styrene Methyl methacrylate |
Vinyl chloride |
| Emulsion polymerization | Styrene Butadiene Acrylate |
Vinyl chloride | |
V. Selection of Polymerization Methods
In the industrial production of polymer compounds, the same polymer can be produced using several different polymerization methods.
Methods that offer the same performance with superior product quality, lower equipment investment, and lower production costs will be developed. Other methods, by contrast, will gradually be phased out.
The choice of polymerization method depends on the properties of the polymer.
For example, the production process of polyvinyl chloride resin can be carried out using any one of several methods. However, the primary particle size obtained via emulsion polymerization is only about 1 micron, making it well-suited for the production of polyvinyl chloride paste.
6. Composition of Emulsion Polymerization Systems
Emulsion polymerization is a process in which monomers and water, under the action of an emulsifier, undergo micellar nucleation—meaning that monomers polymerize within latex micelles to form isolated latex particles (high-molecular-weight polymers).
Polymerization system:
1. Monomer: soft, hard, functional; design Tg.
2. Emulsifiers: Dispersion effect, emulsion stabilization, and solubilization effect;
3. Initiator: Water-soluble thermal initiator;
4. Regulator: Mercaptan chain transfer;
5. Other components: buffer, neutralizer, protective colloid.
7. Selection of Emulsifiers
HLB value—hydrophilic-lipophilic balance. Typically ranges from 1 to 40; the higher the HLB value, the stronger the hydrophilicity. In emulsion polymerization, anionic oil-in-water (O/W) emulsifiers with an HLB value between 8 and 18 are commonly used.
1. Anionic emulsifier
Three-phase equilibrium point—the temperature at which the anionic emulsifier exists in a three-phase equilibrium among molecular dissolution, micelles, and gel.
T p > T Three-phase balance point
2. Nonionic emulsifier
Cloud point—When the aqueous solution of a nonionic surfactant is heated to a certain temperature, the solution changes from transparent to cloudy.
T p
CMC—Critical Micelle Concentration. This refers to the lowest concentration of a surfactant capable of forming micelles.

VIII. New Methods for Emulsion Polymerization

Soap-free emulsion polymerization refers to emulsion polymerization conducted in the absence of any emulsifiers or with only trace amounts of emulsifiers (at concentrations below the critical micelle concentration). This process primarily relies on introducing reactive components that function similarly to emulsifiers, thereby stabilizing the system.
Initiator Fragmentation Method:
Stable colloidal particles are formed by leveraging the steric hindrance effect or electrostatic repulsion of nonionic water-soluble monomers.
Add an ionic monomer to participate in the reaction.
Other:
1. Emulsion interpenetrating polymer networks;
2. Microemulsion polymerization;
3. Emulsion-directed polymerization;
4. Radiation emulsion polymerization;
5. Miniemulsion polymerization;
6. Ultra-concentrated emulsion polymerization;
7. Emulsion polymerization in non-aqueous media. 
Share to:
Related News
A Brief Discussion on Dual-Cure Systems
Since the curing process of UV-curable systems is initiated by light, UV-curable systems also have the following drawbacks: limited curing depth; difficulty in application to colored systems and opaque materials; and inability to cure objects with excessively complex shapes. To address these limitations, dual UV-curing systems have been developed, which combine UV curing with other curing methods. In such systems, the crosslinking or polymerization reaction is accomplished through two independent stages, each operating on a different reaction principle. UV light is used to rapidly set the system or achieve “surface dryness,” while a dark reaction ensures that the “shadowed” areas or inner layers are fully cured, reaching “full dryness.”
Introduction to the UV-CIPP (Ultraviolet Light-Cured In-Place Pipe Repair) Process
After years of operation, various pipelines inevitably suffer from damage and leaks due to factors such as corrosion and poor operational management, leading to significant economic losses. However, replacing the entire pipeline with new ones would not only involve an enormous amount of work but also be costly and time-consuming. Consequently, how to restore pipeline safety efficiently, economically, and quickly has attracted great attention both domestically and internationally. Therefore, research into pipeline repair technologies is of paramount importance.
Encapsulating sealants are used for bonding, sealing, potting, and coating protection of electronic components. Before curing, they exist in a liquid state and exhibit fluidity. The viscosity of the sealant varies depending on the material, performance requirements, and manufacturing process of the product. Encapsulation involves mechanically or manually pouring the liquid composite into devices containing electronic components and circuits, where it cures under ambient or heated conditions to form an excellent thermosetting polymer insulating material with superior performance.