Tel
Tel
+8618142863185
Follow us
Official Accounts
Official Accounts
- Top
A Brief Discussion on Silica Matting Powder
Release time:
2016-05-23 10:19
I. Basic Principles of Light Absorption

The clear-coat film without matting agents exhibits a mirror-like, highly leveled surface. When light strikes the surface of this mirror-like film, part of the incident light is absorbed and part is reflected; the reflected portion imparts gloss to the film. In contrast, the paint film containing silica-based matting agents features silica particles evenly dispersed throughout the film, creating a slightly roughened surface.

The tiny irregularities on the surface of the paint film can cause light to undergo diffuse reflection.

Volatile solvent evaporation: The process by which “streams” are formed within the wet film, moving toward the surface of the paint film and driving the matting agent particles to aggregate in a directional manner toward the surface.
II. Selection of Light-Dimming Methods
1. Incompatibility of the system;
2. High filler content;
3. Wax powder;
4. Organic matting agent: PMMA-PS composite particles;
5. Inorganic matting agent.
III. Inorganic Matting Agents
1. White carbon black, fumed silica, precipitated silica;
2. Surface treatment and untreated surfaces—hydrophilic or hydrophobic;
3. Possesses a larger specific surface area and a unique crystal structure;
4. The microstructure is amorphous or glassy. Compared to natural silica, precipitated silica boasts higher silica purity, greater chemical inertness, superior resistance to ultraviolet light, and a refractive index of 1.46.
IV. Gas-phase precipitated silica
1. Gas-phase precipitated silica: First developed by DEGUSSA in 1941, this method—chemical vapor deposition—involves the high-temperature hydrolysis of silicon tetrachloride vapor in a hydrogen-oxygen atmosphere to form an aerogel. The resulting particles are then aggregated into larger particles via an aggregating device and subsequently collected. The reaction equation is as follows:
2. SiCl₄ + 2H₂ + O₂ → SiO₂ + 4HCl, 1800℃
V. Precipitated White Carbon Black
1. Sodium silicate solution (water glass) is neutralized using an acid (typically sulfuric acid). The byproducts are removed by filtration, and the remaining precipitated silica is dried, loosened, and transformed into a flocculent structure. This method can achieve a maximum specific surface area of up to 500 m²/g.
2. Application performance is determined by the microstructural characteristics of particles formed during the precipitation stage (including composition, ratio, time, temperature, and concentration).
6. Gel-processed precipitated silica
The raw material process route is similar to the precipitation method, with the key difference being that the acid-base reaction proceeds via a sol-gel process. However, the product properties are more comparable to those obtained by the vapor-phase method.
| Company | Modifier |
| GE | D4, HMDZ, DMDC |
| Cabot | HMDZ |
| Dow Corning | HMDZ, PDM |
| Grace | Straight-chain alcohol |
| Degussa | D3, D4, DMDC, Alkoxy Siloxane |
| Wacker | D3, D4, PDMS |
| Rhodia | D3, D4, MM |
| Indonesian Darisa | DUSIL |
1. WACKER: N20, T40, H15, H13L, H20, H17, H18, H2000.
2. Hydrophilicity of Degussa: A200, A300, A380, TT.
3. Hydrophobicity of Degussa: R972, R974, R202, R812, R812S, R106, R8200.
4. CABOT: M-5, EH-5, TS-720, TS-610.
5. TOKUYAMA: QS-102, QS-20, QS-40, DM-10.
6. Jibisheng Gas-phase Silica: H-200, H-150.
7. Factors Affecting Extinction Coefficient
1. Average particle size and distribution of matting agents;
2. Porosity;
3. Bulk density;
4. Surface treatment;
5. The method used;
6. Drying conditions;
7. Coating thickness;
8. Mixed system.
8. General extinction rules
1. Generally speaking, the larger the average particle size of matting agents, the higher their matting efficiency will be.
2. If there are large amounts of “coarse” and “fine” particles—resulting in uneven distribution—this can cause increased viscosity and excessive roughness.
3. The higher the porosity of the matting agent, the higher the content of powder per unit weight will be.
4. The reduction in gloss is due to the particle size effect;
5. At the same particle size, the higher the porosity, the better the effect.
6. Bulk density has no direct correlation with light-scattering performance.
7. The particles are small, with low bulk density, high porosity, and large specific surface area, resulting in a correspondingly increased oil absorption capacity.
8. High oil absorption generally results in better matting performance;
9. The surface treatment offers better matting performance.


9. Infrared Analysis


1. The strong and broad absorption band at 1095 cm⁻¹ corresponds to the asymmetric stretching vibration of the Si-O-Si bond, while the peaks at 806 cm⁻¹ and 476 cm⁻¹ represent the symmetric stretching vibrations of the Si-O bond.
2. The broad peak at 3442 cm⁻¹ is the asymmetric stretching vibration peak of structural water-OH.
3. Near 1636 cm⁻¹ is the bending vibration peak of the H-O-H bond in water;
4. The peak at 955 cm⁻¹ corresponds to the bending vibration absorption peak of Si-OH. 
Share to:
Related News
Surface Treatment Secret: Electrolytic Polishing
Electropolishing involves using the workpiece to be polished as the anode and an insoluble metal as the cathode. Both electrodes are simultaneously immersed in an electrolytic cell, and a direct current is passed through the cell, triggering an electrochemical reaction that selectively dissolves the anode material. As a result, fine burrs on the workpiece surface are removed, and the surface brightness is enhanced.
Principles and Applications of Fourier Transform Infrared Spectroscopy (FT-IR)
When a sample is irradiated with infrared light whose frequency varies continuously, molecules absorb radiation at certain frequencies, causing a net change in their dipole moments due to their vibrational or rotational motions. This results in transitions of molecular vibrational and rotational energy levels from the ground state to excited states, thereby reducing the intensity of transmitted light corresponding to these absorption regions. By plotting the percentage transmittance of infrared light against wavenumber or wavelength, one obtains the infrared spectrum.
Application of High-Performance UV Resins in Vacuum Electroplating Coatings
Plastic materials are widely used, easy to mold, and lightweight. Mold injection molding offers excellent dimensional stability and can produce intricate surface textures that are difficult to achieve with any metal material. After electroplating, the surface becomes metallic, giving it a high-quality metallic finish. These plastics can serve decorative purposes as well as provide protection against electromagnetic interference, reflection, or anti-reflection effects.