News

Knowledge

Company News

Application Mind Map

Test Report

Technical Article

Industry News

Typical Defects of UV Resins on Difficult-to-Bond Substrates (Part 7)

Typical Defects of UV Resins on Difficult-to-Bond Substrates (Part 7)

Insufficient adhesion durability is a typical defect that can emerge in UV‑curable resins applied to difficult‑to‑bond substrates over prolonged service. It manifests as acceptable initial adhesion scores, followed by a marked decline after exposure to thermal cycling, humidity, or aging tests. This issue is particularly critical in applications such as automotive interiors and appliance panels, where long‑term performance is essential, directly impacting the service life and reliability of the coating system. Because these resins rely on adhesion promoters and modifying additives to achieve initial adhesion, their interfacial bonding mechanisms exhibit different stability under long‑term environmental conditions compared with conventional UV‑curable resins, necessitating systematic analysis and targeted mitigation strategies.

10

2026

/

10

Typical Defects of UV Resins on Difficult-to-Bond Substrates (VI)

Typical Defects of UV Resins on Difficult-to-Bond Substrates (VI)

Surface defects are a typical challenge encountered when applying UV‑curable resins to difficult‑to‑adhere substrates, manifesting as irregularities such as craters, orange‑peel texture, or residual air bubbles on the coating surface. This issue is particularly critical in applications with stringent aesthetic requirements—such as automotive interiors and appliance panels—where it directly impacts both visual smoothness and protective performance. Because these substrates exhibit low surface energy, the wetting and spreading behavior of the coating differs from that on conventional substrates; consequently, the causes and manifestations of surface defects are unique and demand systematic analysis and targeted mitigation strategies.

09

2026

/

10

Typical Defects of UV Resins on Difficult-to-Bond Substrates (Part 5)

Typical Defects of UV Resins on Difficult-to-Bond Substrates (Part 5)

In multi‑coat coating systems, intercoat adhesion is a common issue and one of the key defects that must be carefully addressed when applying UV‑curable resins to substrates with poor adhesion. Without strong intercoat bonding between the primer and topcoat, the topcoat may delaminate or blister, compromising the coating system’s aesthetic integrity, protective performance, and service life. For applications such as automotive interiors and appliance panels—where both appearance and durability are critical—insufficient intercoat adhesion can lead to premature coating failure during assembly, use, or environmental aging. Therefore, it is essential to systematically analyze the root causes and implement targeted corrective measures.

09

2026

/

10

Typical Defects of UV Resins on Difficult-to-Bond Substrates (Part 4)

Typical Defects of UV Resins on Difficult-to-Bond Substrates (Part 4)

Insufficient chemical resistance is a typical drawback of UV‑curable resins on difficult‑to‑adhere substrates in specific application scenarios, manifesting as swelling, discoloration, or performance degradation upon exposure to chemicals. This issue is particularly critical in applications such as automotive interiors and appliance panels, which are subjected to prolonged chemical contact, directly impacting product service life and the ability to maintain aesthetic appearance. Due to the incorporation of adhesion promoters and modified resin components, the chemical resistance of UV‑curable resins for challenging substrates differs from that of conventional UV resins, necessitating systematic analysis and targeted mitigation strategies.

09

2026

/

10

Typical Defects of UV Resins on Difficult-to-Bond Substrates (Part 3)

Typical Defects of UV Resins on Difficult-to-Bond Substrates (Part 3)

Whitening or haze in coatings is a common defect in UV‑curable resin applications on difficult‑to‑adhere substrates, compromising optical performance. It manifests as reduced transparency in the cured film, resulting in a milky, whitish appearance. This issue is particularly critical in transparent coatings and optical applications, directly impacting both aesthetic quality and optical functionality. In coating systems applied to challenging substrates, the root causes of whitening share similarities with those observed in conventional UV resins; however, factors such as substrate surface treatment, the incorporation of adhesion promoters, and the use of modified resins introduce distinct nuances.

08

2026

/

10

Typical Defects of UV Resins on Difficult-to-Adhere Substrates (Part 2)

Typical Defects of UV Resins on Difficult-to-Adhere Substrates (Part 2)

Curing shrinkage is an intrinsic property of UV‑curable resins during the polymerization process; however, on substrates with poor adhesion, the interfacial stresses generated by shrinkage are more likely to cause debonding. This issue is particularly pronounced on substrates such as polyesters, which are highly sensitive to shrinkage‑induced stresses. During curing, the coating undergoes volumetric contraction, and the resulting shrinkage stresses concentrate at the coating–substrate interface. When these stresses exceed the interfacial adhesion strength, the coating delaminates from the substrate. Understanding the mechanisms underlying this defect and the factors that influence it enables the implementation of targeted control measures in practical production.

08

2026

/

10

Typical Defects of UV Resins on Difficult-to-Bond Substrates (Part 1)

Typical Defects of UV Resins on Difficult-to-Bond Substrates (Part 1)

Insufficient adhesion is a typical defect in the application of UV‑curable resins to difficult-to-bond substrates, manifesting as coating delamination or lifting from the substrate surface. Although these resins are specifically formulated to address adhesion challenges on low‑surface‑energy plastics, substandard adhesion can still occur in practice due to various factors. This defect directly results in unacceptable product appearance and reduced reliability, making it a critical issue that requires close attention during the coating process.

08

2026

/

10

Applications of UV Resins on Difficult-to-Bond Substrates

Applications of UV Resins on Difficult-to-Bond Substrates

UV‑curable resins for difficult-to-bond substrates, with their proven ability to achieve reliable adhesion on low‑surface‑energy plastics, have already found practical applications across numerous industrial sectors. From automotive interiors to consumer electronics, and from packaging materials to medical devices, these resins offer viable solutions for coating and bonding substrates such as polypropylene, polyethylene, and polyester. Gaining a clear understanding of their application areas and specific use cases helps to better appreciate the technology’s industrial value and its future development trajectory.

07

2026

/

10

< 1234...162 >