Tel
Tel
+8618142863185
Follow us
Official Accounts
Official Accounts
- Top
Detailed Explanation of Ceramic Decal Application Technique
Release time:
2016-03-28 16:25
Preface
In our daily lives, we often see beautifully crafted patterns on ceramic bowls and plates—patterns that are exquisite and incredibly delicate. The floral designs on ceramics are not only heat-resistant but also resistant to chipping and discoloration. But did you know how these intricate floral designs are applied in the first place?

In fact, ceramics are an ancient traditional craft in China, embodying thousands of years of the country’s history and culture. Through continuous improvements, today’s decorative patterns on everyday ceramic ware are predominantly created using the decal transfer technique.
I. Ceramic Science Popularization
1. Encyclopedia of Ceramics
(1) Ceramics is a general term encompassing both earthenware and porcelain;
(2) The distinction between earthenware and porcelain lies in two key factors: first, the materials used; and second, the firing temperature. Both factors are indispensable. Earthenware can be made from a variety of mineral clays, including porcelain clay, and is fired at relatively low temperatures—typically ranging from 700 to 1,000°C. Its body is essentially sintered, no longer disintegrating upon contact with water, yet it exhibits a higher porosity and water absorption rate. Under a microscope, the body contains very few glassy phases or mullite crystals—meaning it has not fully vitrified—and when tapped, its sound is rather dull. In contrast, porcelain is fired from porcelain clay that has a high alumina content, known as kaolin. Porcelain is fired at temperatures of at least 1,100°C or higher, resulting in a body that is essentially vitrified. Microscopic examination reveals abundant mullite crystals, lower porosity and water absorption rates, and a crisp, resonant sound when tapped.
(3) People invented pottery as early as about 8,000 years ago during the Neolithic period;
(4) Common ceramic materials include clay, alumina, and kaolin, among others.
(5) Ceramic materials generally have high hardness but poor plasticity.
(6) Ceramic raw materials are derived from large quantities of naturally occurring clay resources found on Earth through extraction and refining. Clay possesses unique properties: at room temperature, it becomes pliable when wet; slightly dried, it can be carved; and when fully dried, it can be ground into fine powder. When fired at 700 degrees Celsius, it transforms into pottery capable of holding water. When fired at 1230 degrees Celsius, it vitrifies, becoming virtually impermeable to water and highly resistant to both high temperatures and corrosion.
(7) Ceramic materials are mostly oxides, nitrides, borides, and carbides, among others.
2. Ceramic Properties
(1) Mechanical Properties: Ceramic materials are among the engineering materials with the highest stiffness and hardness, with most having a hardness exceeding 1500 HV. Ceramics exhibit high compressive strength but relatively low tensile strength, and they have poor ductility and toughness.
(2) Thermal Properties: Ceramic materials generally have high melting points (most above 2000℃) and exhibit excellent chemical stability even at high temperatures. The thermal conductivity of ceramics is lower than that of metallic materials, yet ceramics also serve as effective thermal insulators. Moreover, the linear thermal expansion coefficient of ceramics is lower than that of metals; thus, when subjected to temperature changes, ceramics maintain good dimensional stability.
(3) Electrical Properties: Most ceramics exhibit excellent electrical insulation properties, making them widely used in the manufacture of insulating components designed for various voltage levels (1 kV to 110 kV).
(4) Chemical Properties: Ceramic materials are resistant to oxidation at high temperatures and exhibit excellent corrosion resistance against acids, bases, and salts.
(5) Optical Properties: Ceramic materials also possess unique optical properties and can be used as solid-state laser materials, optical fiber materials, optical storage devices, and more. Transparent ceramics can be employed in high-pressure sodium lamps, among other applications.
3. Applications of ceramics
(1) Daily-use ceramics: such as tableware, tea sets, jars, basins, bowls, and plates;
(2) Artistic (craft) ceramics: such as vases, sculptures, vessels, picture frames, murals, and the like;
(3) Industrial ceramics: architectural ceramics, sanitary ceramics, chemical ceramics, electrical porcelain, and special ceramics.

4. History of Chinese Ceramics
The origin of China’s English name, “China,” is as follows: Changnan (porcelain) – China – China.
A History of Ceramic Development in China Through the Ages
(1) Xia, Shang, and Zhou Dynasties: Early porcelain, proto-porcelain;
(2) Qin and Han Dynasties: Lead-glazed pottery, celadon-glazed pottery;
(3) The Three Kingdoms, Two Jin, and Northern and Southern Dynasties: Celadon;
(4) The Tang Dynasty: The dawn of the true porcelain era. The most important product was the renowned Tang Sancai, celebrated both at home and abroad.
(5) The Song Dynasty: Achieved a pinnacle in porcelain craftsmanship. The Five Great Kilns: Ding Kiln, Ru Kiln, Guan Kiln, Ge Kiln, and Jun Kiln;
(6) Yuan Dynasty: Blue-and-white and underglaze red wares emerged, and colored porcelain became widely popular;
(7) The Ming Dynasty: Primarily featured white porcelain, with Jingdezhen becoming the most important kiln site.
(8) Qing Dynasty: Chinese porcelain can be said to have reached the pinnacle of perfection.
(9) Modern: daily-use ceramics, architectural ceramics, sanitary ceramics, and art ceramics.
5. Current Status of China’s Ceramic Development
China is a global center for ceramic manufacturing and a major ceramic-producing country, ranking first in the world in both annual production and exports. Daily-use ceramics account for 70% of the global market, decorative art ceramics account for 65%, sanitary ceramics account for 50% of global production, and architectural ceramics account for 64% of global production.
Statistics on the Growth of China's Ceramic Export Trade Volume from 2007 to 2013

6. Famous ceramic production area
(1) Jingdezhen, Jiangxi Province: Jingdezhen is famously known as the “Porcelain Capital.” It is a major production base for four renowned types of porcelain—blue-and-white, famille rose, delicately carved, and colored glaze—as well as for everyday ceramic ware.
(2) Liling, Hunan: China’s second-largest porcelain capital;
(3) Dehua County, Quanzhou, Fujian: China’s third-largest porcelain capital and the country’s largest base for the production and export of Western-style ceramic ware.
(4) Tangshan, Hebei: Known for its top-quality white jade porcelain, bone china, and magnolia porcelain—these three types represent the finest in high-end ceramics. As a pioneer in modern and contemporary Chinese ceramic machinery, the region boasts over 1,000 ceramic enterprises. Daily-use ceramics account for 70% of the province’s total output and 14% of the nation’s total.
(5) Handan, Hebei: A renowned Chinese production base for high-end porcelain and folk ceramics;
(6) Zibo, Shandong: Zibo is one of China’s five major porcelain capitals and an important ceramic production center nationwide.
(7) Foshan City, Guangdong Province: China’s largest production base for architectural and sanitary ceramics.
(8) Chaozhou City, Guangdong Province: A renowned Chinese base for the production and export of artisanal ceramics. Fengxi District in Chaozhou is the most densely concentrated area for the city’s ceramic industry, home to over 2,500 ceramic enterprises.
7. Ceramic Production Process (Traditional Handcraft)
(1) Clay Preparation: The first step in porcelain production—slurry preparation—is the process of refining clay into workable porcelain clay.
(2) Wheel throwing: Wheel throwing is the first step in the forming process;
(3) Mold pressing: The outer shape of the mold is carved by rotating along the curved inner surface of the blank.
(4) Body Shaping: Body shaping, also known as “trimming” or “turning,” is the crucial final step in defining the shape of the ceramic piece.
(5) Drying the greenware: Place the shaped greenware on wooden racks to dry.
(6) Carving: Use knives made of bamboo, bone, or iron to carve patterns onto the dried body.
(7) Glazing: Most ceramic products must be glazed before being fired in the kiln.
(8) Kiln firing: The kiln firing process lasts approximately one day and one night, with the temperature reaching around 1300 degrees Celsius.
(9) Painting: Patterns and colors are applied onto the glaze of already-fired porcelain, then the piece is fired again in a kiln at a low temperature—approximately 700–800 degrees Celsius.
(10) Changes in glaze color: The pigment colors observed by the artist when applying glaze and painting on the raw, unglazed body undergo significant changes after being fired and baked at high temperatures.
8. Flowchart of Ceramic Manufacturing Process

II. Introduction to Ceramic Decals
1. Definition
Ceramic decal application is a technique in which colored patterns from decorative paper are transferred onto ceramic bodies or glazes using an adhesive method. It is also known as "flower transfer." This is one of the most widely used decorative techniques in modern ceramics.

2. Classification

3. According to the different backing papers used for printing
(1) Large film decal
The backing paper is made of wood pulp paper with a basis weight of approximately 180 g/㎡. A PVC film is laminated onto its surface using a hot-pressing method. A very thin PVB plastic film is then formed by coating a polyvinyl butyral (PVB) solution—dissolved in ethanol—onto the aforementioned base paper. The patterns of the decorative paper are printed onto this PVB film, a technique known as the "large-film decal method."
(2) Small film decal
Using highly absorbent photographic base paper with a basis weight of 120–180 g/㎡, a water-soluble adhesive layer is applied to the surface. Floral patterns are then printed onto this adhesive layer. Finally, a cover coat consisting of a poly(methyl methacrylate) solution is applied over the pattern using screen printing. After drying, a thin film is formed, known as small-film decal paper.
(3) Underglaze decal paper
The decorative pattern is printed onto a very thin cotton silk paper (the base paper used for mimeograph stencils) using a water-soluble ink paste; this type of paper is called underglaze decal paper.
4. Schematic diagrams of the three types of decalcomania paper structures

5. Classified by printing method
(1) Offset-printed (lithographic) decal paper
(2) Screen-printed decal paper
(3) Rotogravure decal paper: Less commonly used.
The most widely used among them is screen-printed decal paper.

6. Characteristics of Three Types of Ceramic Decal Papers
| Offset printing decal paper | Screen-printed decal paper | Rotogravure decal paper |
| Both large membranes and small membranes can be printed on. | Both large membranes and small membranes can be printed on. | Cotton silk paper |
| Use oxidative polymerization drying oil-based ink, slow-drying. | Use volatile-drying oil-based ink, fast-drying. | Water-soluble ink adjusting paste |
| Suitable for printing on overglaze decal paper. | Suitable for printing on-glaze and in-glaze decal paper. | Only printed underglaze decal paper |
| The printed color layer is relatively thin (single-color): 3–6 µm. | The printed color layer is relatively thick (single color): 10–15 µm. | The coating thickness is approximately 28–30 µm. |
| Fast printing speed (offset printing): 70–80 sheets/min | 30-40 sheets/min | Generally manual printing. |
| Do not print in selenium red (bright red), white, gold glue, or silver glue. | All pigments, gold glue, silver glue, relief effects, and recessed effects are printable. | Generally, only blue-and-white decal paper is printed. |
| After color firing, it exhibits slightly poorer resistance to acids, alkalis, and abrasion. | Good acid resistance, alkali resistance, and abrasion resistance. | Best acid-resistant, alkali-resistant, and abrasion-resistant. |
| The printed materials are finely detailed and richly colored; even with the use of a buffing process, they can still produce glossy, high-end decal paper. | The printed materials feature fine detail, rich colors, strong three-dimensionality, and a glossy finish; they are suitable for printing high-end decal paper with multi-color halftone patterns. | The color tones are relatively simple, and the printing mainly features lines and solid blocks. |
III. Key Introduction to Screen-Printed Decals
1. Definition
(1) Screen-printed decals—also known as small film decals or water-transfer decals—are a decorative technique in which patterns are first printed onto a special paper pre-coated with a water-soluble adhesive. After being soaked and moistened in water, these decals are then transferred and adhered to the surface of an object.
(2) Small film decals are primarily used for decorating irregular surfaces of objects such as ceramics, glass, sports equipment (helmets, rackets, etc.), metals, and wood products.

2. Composition
It consists of a base paper (also known as the paper substrate) at the bottom, a sol-gel layer in the middle, and a surface coating oil on top.
Structural diagram

3. Classification
(1) According to the different baking temperatures after transfer printing, they can be classified into high-temperature transfer paper and low-temperature transfer paper.
(2) High-temperature decorative papers: These include ceramic high-temperature firing decorative papers and glass high-temperature firing decorative papers. Ceramic decorative papers, in turn, can be further classified into overglaze decorative papers and underglaze decorative papers.
(3) Low-temperature transfer paper: Primarily used on sports equipment, metals, wood products, and other materials. After the transfer paper is applied to the substrate, it only requires low-temperature baking below 200℃.
4. Features
Compared with other transfer decal papers, the greatest advantage of small-membrane flower paper lies in its clear lines and dots, fine tonal gradations, and flexible film layer. Therefore, it is the best choice for producing high-end floral papers.
5. Manufacturing Process
(1) The production process of small film decorative papers is mainly divided into pre-printing preparation, in-process control, and post-printing inspection. For small film decorative papers—especially high-temperature decorative papers (such as ceramic and glass decorative papers)—the pre-printing stage is particularly crucial, encompassing design, color separation, plate-making, and material selection.
(2) High-quality small-membrane flower paper features distinct and delicate image layers, saturated colors, accurate color registration, no turtle-shell patterns, and no defects in the image. When transferred, it exhibits excellent stretchability and is resistant to tearing, delivering ideal baking results. Whether these quality requirements can be met largely depends on the various pre-press processes.
6. Technical Parameters
(1) Ceramic decal paper is primarily used for decorating ceramic ware with patterns and colors, replacing the previously common hand-painting and spray-painting techniques.
(2) The resolution of screen-printed ceramic decal paper can reach 40–50 lines/cm;
(3) After the screen-printed ink patterns on ceramic decal paper are transferred onto ceramic ware, they must be fired at temperatures ranging from 700–800°C or 1100–1350°C to ensure firm adhesion. The color of the pattern depends on the type of colorant used in the ceramic.
(4) Ceramic decal paper serves as the carrier for ceramic inks and is divided into overglaze decal paper and underglaze decal paper. The types of decal paper differ based on their composition.
(5) Due to the strong opacity and poor transparency of ceramic inks, it is currently not possible to use the three-primary-color principle for printing. Instead, a dot-matrix printing method is employed, using specially designed color ink dots arranged side by side without overprinting.
(6) The ink used for printing on-glaze decal paper is a high-temperature solvent-based ink; the ink used for printing under-glaze decal paper is a high-temperature water-based ink.
IV. General Process Flow for Ceramic Production
1. Creating white-bodied vessel forms
Many companies that produce everyday ceramic tableware create suitable ceramic body samples either based on OEM orders or by designing their own prototypes tailored to local customs and trends. The process is rather complex, and developing a new body shape requires significant financial and human resources—such as mold making and trial firings.

2. Design floral paper
Based on the shape of the ceramic white body, the designer begins to work on the floral pattern. Typically, floral patterns are designed around a single overarching theme. Using the unfolded plan view of the ceramic white body as a reference, the designer creates the floral motif. The colors used in the floral design must be produced according to the ceramic pigment manufacturing process—rather than being chosen arbitrarily by the designer. Generally speaking, the more color varieties there are, the higher the cost of the floral pattern will be.

3. Ceramic decal
The designed floral paper is printed and produced by a floral-paper factory. A good piece of work is achieved when the final result matches the designer’s intended effect. Next, the floral paper is applied onto a ceramic white body. Before applying the floral paper, the white body should be soaked in clean water for half an hour, after which the floral paper can be carefully adhered to it. Once all the moisture has completely dried—this includes any moisture absorbed by the white body—the piece can be fired in the kiln. This firing process typically takes more than three hours.

4. Ceramic baking
We place the decorated ceramic pieces into a tunnel kiln for firing. This process is relatively slow—taking about four hours to complete—with the kiln temperature carefully maintained around 800 degrees Celsius. Haha, and just like that, a beautiful ceramic piece is ready!
V. Ceramic Floral Paper Manufacturing Process
1. Manufacturing Process Flow
(1) The sole function of ceramic decal paper is to decorate and beautify ceramics.
(2) The production process of ceramic decal paper is divided into pre-printing, in-printing, and post-printing stages.
(3) Pre-press includes the creation and design of ceramic decal paper artwork, color separation and plate-making, and proofing.
(4) Printing includes paper processing, formulation of ceramic pigment inks, and printing;
(5) Post-printing includes inspection, sorting, and packaging.
2. Printing Process Flow

3. Process Flowchart for Printing

4. India-China
(1) Screen mesh selection
The standard screen mesh is a 300T polyester mesh. This mesh produces color layers that closely meet the requirements for ceramic pigments, and both the mesh and pigment costs are low, making it the most ideal choice for printability during production.
(2) In general, for printing cover coatings, use a screen mesh with 60–80 mesh; for printing halftone patterns, use a screen mesh with 300–380 mesh; for printing gold paste onto ceramic decal paper, use a 380-mesh screen; and for printing gold paste onto glass decal paper, use a 350-mesh screen (glass decal paper requires excellent opacity). As a general rule, for screen meshes with 200 mesh or higher, it is advisable to use imported screen fabric.
(3) Color adjustment
Screen-printing ceramic ink is prepared by mixing a colorant (ceramic pigment) with an ink vehicle oil in a specific ratio (the mixing ratio should be determined based on the specific gravity of the pigment). The viscosity must be suitable for screen printing. Typically, the mixing ratio is pigment : ink vehicle oil = 100 : 40–80.
5. India-China control
Ceramic decal paper is produced using screen-printing technology. The key aspects of this process include ensuring accurate color registration, achieving thick and glossy color layers, and maintaining clear tonal gradations in the pattern.
(1) Accurate color matching
There are three key factors that affect the accuracy of color registration: a. Whether the paper feed system of the printing press is properly adjusted to ensure that the paper is accurately positioned as it moves from the paper feed table to the printing register; b. Whether the tension of each screen mesh is consistent; c. Whether the paper expands or contracts due to changes in temperature and humidity in the workshop during multiple printing passes. If these three factors are properly addressed, color registration will certainly be accurate.
(2) Control of Color Layer Thickness
An important criterion for determining the quality of ceramic decal paper is whether it can accurately reproduce the colors of the original artwork. To properly control the thickness, it’s essential to pay attention to three key factors: screen mesh count, coating thickness of the photosensitive emulsion, and printing parameters.
(3) The layers of the pattern
6. Composition of screen-printing ceramic inks
(1) Vehicle: Solid resins and organic solvents that dissolve the resins—these constitute the film-forming substance;
(2) Colorants: These are metal oxides that determine the color hue after firing.
(3) Additives: These enhance the brightness of pigments and ensure that screen-printed ceramic inks fuse seamlessly with the ceramic glaze after firing and coloration. Typically, they consist of lead-based glassy materials and low-melting-point boron compounds.
7. Precautions for applying decals
(1) The temperature in the screen-printing workplace should be maintained within the range of 22–26°C, with a relative humidity of 65–70% being ideal.
(2) For transfer decals used in underglaze multicolor screen printing, before screen printing, the paper should first be brought into the screen-printing area for several days (depending on the weather conditions). Printing should be carried out only after the paper has stabilized in terms of expansion and contraction.
(3) For multi-colored decalcomania paper, after each color has been printed and dried, it should be allowed to air for a certain period of time. Only after the paper’s moisture content has returned to normal can the next color be printed.
(4) Porcelain inks used for screen printing have poor miscibility. If mixed improperly, they may undergo chemical reactions during firing, leading to issues such as color deterioration or blooming. Therefore, it is advisable to select porcelain inks with good compatibility whenever possible.
8. Summary of Printing Process Issues
(1) The heat-curing inks and heat-curing cover coatings currently in use contain large amounts of solvents and have a strong odor.
(2) The curing time is relatively long, resulting in low production efficiency.
6. Water Transfer Printing Process Flow
1. Process Flow

2. Water Transfer Printing Flowchart

3. Precautions
(1) When applying the decorative paper, no air bubbles should be trapped beneath it. You must use a soft squeegee to carefully remove any air bubbles; otherwise, the flowers are likely to crack during the firing process.
(2) The curvature of the floral paper design cannot be perfectly accurate, as the floral paper itself tends to shrink. Therefore, as long as it doesn’t compromise the aesthetic appeal, that’s fine.
(3) When applying the decal paper, don't stretch it excessively. If you do, the areas that have been stretched will appear lighter in color after baking, which will affect the overall appearance of the design.
(4) Glaze. The pattern on the decorative paper is printed onto adhesive-coated paper. When applying, the paper is soaked in water, allowing the pattern to detach easily. The pattern is then affixed to the porcelain. For underglaze decoration, the floral design is applied first, followed by glazing; the firing temperature depends on the type of glaze used. For overglaze decoration, the porcelain is fired first, and then the floral design is applied afterward—at a firing temperature of around 800 degrees Celsius.
(5) When the firing temperature is too low, the printed design may peel off at the slightest touch, indicating poor adhesion.
4. Ceramic Printing Case Study (Tangshan Xinrui Flower Paper Factory)

Share to:
Related News
Introduction to UV Absorbers and Their Applications
Ultraviolet absorbers are a class of substances that can prevent the degradation of polymers caused by sunlight or other artificial ultraviolet light; they are a type of light stabilizer. The use of ultraviolet absorbers can effectively protect treated objects from, or at least mitigate, damage to their color. Since different types of polymers are susceptible to degradation at different ultraviolet wavelengths, various ultraviolet absorbers can absorb different wavelengths of ultraviolet light. Therefore, when selecting an ultraviolet absorber, it is essential to take into account the specific type of polymer involved.
Introduction to Wood UV Coatings and Their Applications
Wood UV lacquer, also known as nitrocellulose lacquer, is a coating whose primary film-forming substance is nitrocellulose and which dries through natural evaporation. This type of coating offers significant advantages when used for finishing export furniture products and is highly favored by foreign buyers from Europe and the U.S. The key advantage of nitrocellulose lacquer lies in its rapid drying time—while conventional paints typically require 24 hours to dry, nitrocellulose lacquer can dry in just a dozen minutes or so. This dramatically boosts work efficiency and reduces costs.