Tel
Tel
+8618142863185
Follow us
Official Accounts
Official Accounts
- Top
Introduction to UV Matte Coatings for PVC Flooring
Release time:
2025-06-03 15:06
1
Introduction to PVC
1. PVC (polyvinyl chloride), known in Chinese as “plastic flooring,” is primarily composed of polyvinyl chloride material.
2. They are mainly divided into flexible rolls and rigid sheets. Among the rigid types, common ones include PVC ceiling panels, edge trims, and LVT (laminate flooring—formed by pressing, semi-rigid); with SPC (extruded flooring—rigid flooring) being the primary type. As for the flexible types, common ones include homogeneous core materials and PVC veneers.
3. The manufacturers primarily come from the wood-coating industry and have adopted wood-coating standards for their testing equipment and methods.
4. Directions for later improvements: PP flooring, melamine flooring, etc.
5. LVT Process Flow: Foaming and Molding → Hot-Melt Adhesive Bonding → Curing → Coating → Tempering → Cutting → Grooving → Packaging
6. SPC Process Flow: Extrusion Molding → Cutting → Coating → Cutting → Grooving → Packaging
2
UV Coating Roller Application Process
PVC plastic flooring → Preheating section → UV primer roller coating → UV curing → UV topcoat roller coating → Heating and leveling section → UV curing → Inspection and board collection
3
Construction process parameters
1. Preheating Section: During winter when temperatures are low, the heater should be turned on; it is not needed during summer.
2. Primer roller coating: Apply primer at 4–6 g/m² using a roller.
3. Primer curing: UV lamp power 10–15 kW. Adjust the lamp height and chain speed to ensure that the UV lamp intensity is between 200–300 mW/cm² and the energy density is between 150–300 mJ/cm². The lamp’s service life is less than 800–1,000 hours.
4. Topcoat Roller Coating: Adjust the application amount of the topcoat roller coating according to the substrate texture and customer requirements.
5. Heating and Leveling Section: Adjust according to ambient temperature and the desired gloss level of the finished product. When the ambient temperature is low, turn on the heating; if the gloss level is too high and needs to be reduced, also turn on the heating.
6. Topcoat curing: UV lamp power 10–15 kW. Adjust the lamp height and chain speed to ensure that the UV lamp intensity is between 600–1000 mW/cm² and the energy density is between 600–1000 mJ/cm². The lamp’s service life is less than 800–1000 hours.
7. Precautions for UV Energy Testing:
A. Ultraviolet light is light with wavelengths ranging from 40 to 400 nm, and can be further divided into:
UVA: Near Ultraviolet
UVB: Mid-ultraviolet
UVC: Vacuum Ultraviolet
B. Matte coatings require UV light in the UVA wavelength range for curing.
What needs to be recorded for UV energy meter testing is:
UVA band light energy, unit: mj/cm²; light intensity, unit: mw/cm².
4
Coating composition
1. Epoxy/Polyurethane/Polyester Acrylate
Provides film-forming substances that enable the coating to crosslink and form a film, imparting properties such as film hardness and scratch resistance.
2. Photoinitiator
After being exposed to UV curing lamps, the photoinitiator provides activation factors that cause the coating to cure.
3. UV monomer
Low-viscosity resin, used as a solvent substitute to adjust the viscosity of coatings and participate in the curing and film formation of coatings.
4. Powdered material
Matte coating components, which provide a matte finish after the coating has cured.
5. Additives
Provide respective performance based on specific requirements.
5
SPC matte coating
1. Primer
Use: Enhances adhesion between the coating and the substrate, is used in conjunction with topcoats, and helps adjust the overall appearance and performance of the paint film.
Testing Item (Coating):
Appearance: Milky white or pale yellow gel-like liquid
Viscosity (cps/25℃): 600-1000 cps
Odor: None
Storage stability (80℃ × 72h): No precipitation.
Recommended recipe:
| Raw materials | Proportion | Note |
| B-165 | 15.6 | Modified epoxy acrylate |
| B-335 | 9.4 | Easy-to-Deplete Polyurethane Acrylate |
| B-574C | 12.5 | Polyester acrylate |
| HEMA | 9.4 | Hydroxypropyl methacrylate |
| HDDA | 28.1 | 1,6-Hexanediol diacrylate |
| 1173 | 3.8 | Photoinitiator |
| LTW | 1.2 | Adhesion promoter |
| BYK2013 | 1.3 | Wetting and dispersing agent |
| 872 | 12.5 | Matte powder |
| G520 | 6.2 | Matte powder |
| Total | 100 |
2. Topcoat
Applications: The coating provides specific matte finish, high hardness, and excellent scratch resistance.
Testing Item (Coating)
Appearance: Milky white or pale yellow gel-like liquid
Viscosity (cps/25℃): 600-1500 cps
Odor: None
Storage stability (80℃ × 72h): No precipitation.
Recommended recipe:
| Raw materials | Proportion | Note |
| B-165 | 12 | Modified epoxy acrylate |
| B-335 | 9 | Easy-to-Deplete Polyurethane Acrylate |
| B-574C | 15 | Polyester acrylate |
| B-828/B-601 | 6 | Functional resin: stain-resistant/wear-resistant |
| HDDA | 30 | 1,6-Hexanediol diacrylate |
| BI-750C | 4.8 | Photoinitiator |
| BYK2013 | 2.4 | Wetting and dispersing agent |
| 872 | 12 | Matte powder |
| G520 | 6 | Matte powder |
| PM | 3 | Solvent |
| Total | 100 |
Testing items:
Test Item Name |
Test results |
Primer roller coating thickness |
4-6g |
Topcoat roller coating thickness |
6-8g |
Coating appearance |
Visually uniform, feels smooth and silky to the touch. |
Gloss/Glossmeter |
Gloss meter testing |
Odor after curing |
Odorless |
Adhesion/3M Tape |
5B |
Scratch-resistant (hand-scratched) |
No scratches |
Scratch-resistant (scratched by a coin) |
No scratches |
Wear-resistant (Martindale test) |
3M scrubbing sponge, 4N, 160 uses, Grade 1-2 |
Abrasion-resistant (Taber) |
250g grinding wheel, 500 cycles, <0.015g |
Scratch-resistant (needle scratch) |
1.0mm needle, as required, >2500g or 3000g |
Rubbing against each other |
No scratches |
Stain-resistant |
Oil-resistant pen, erasable |
6
Analysis of Formulation Challenges
1. Odor: Generally, customers have environmental protection requirements and demand products with low or no odor. However, both resin raw materials and monomers themselves carry some odor, and photoinitiators release odor during curing, which can result in odors in coatings and finished boards.
2. Viscosity Changes: During continuous application, the viscosity of the coating gradually increases due to factors such as roller shear and ambient temperature fluctuations. This ultimately leads to interruptions in roller coating or an increasing amount of coating applied to the board, affecting gloss and appearance quality, and even causing a sharp decline in the performance of the paint film, thereby reducing the yield of good-quality products.
3. Abrasion and Scratch Resistance: Since PVC roller coating typically involves a single topcoat and one undercoat—rather than the multiple coats, such as five undercoats and four topcoats, used in wood flooring—the coating weight is only 10–15 mg. As a result, its abrasion and scratch resistance are significantly inferior to those of wood flooring.
4. Low Gloss: Typically, customers require the gloss of the板材 to gradually decrease from 10–15° to 8–10°, then to 5–8°, and finally to around 3°. As the gloss becomes progressively lower, the amount of matting agent added to the formulation must increase accordingly. This ultimately leads to a series of issues, including increased viscosity, reduced formulation stability, and diminished abrasion and scratch resistance of the coating film.
5. Inconsistencies in the customer’s substrate boards, coupled with the increasing recycling of mixed materials, are leading to reduced adhesion; deeper surface textures are causing uneven coating application and declining wear and scratch resistance.
6. There are no unified standards for customer roller coating equipment or testing equipment, so products need to be customized based on the specific site conditions of each customer.
7. Competition among paint manufacturers is intensifying, and the decline in prices has led to a significant reduction in formulation costs. As a result, it’s becoming increasingly challenging to develop new formulations while maintaining existing performance levels or meeting even higher performance requirements.
7
Resin Recommendations
| Product Model | Product Type | Functional group | Feature |
| B-912 | Polyurethane acrylate | 10 | Excellent resistance to yellowing, abrasion resistance, and excellent flexibility. |
| B-165 | Modified epoxy acrylate | 2 | Excellent yellowing resistance and excellent wetting and dispersibility on matte powder. |
| B-335 | Polyurethane acrylate | 3 | Excellent light extinction performance, excellent stability, and excellent toughness. |
| B-328M | Polyurethane acrylate | 3 | Excellent matting effect, delicate hand feel, and excellent adhesion. |
| B-574C | Polyester acrylate | 6 | Fast curing, low viscosity, and excellent wetting and dispersing properties with matte powders. |
| B-828 | Silicone-based UV-curable resin | 6 | Good leveling, smooth and slick, dirt-resistant. |
| B-601 | Polyurethane acrylate | 6 | High hardness, high wear resistance, and cost-effective. |
Share to:
Related News