Analysis of Common Issues with UV PCB Ink (Part 2)


In the manufacturing process of PCBs (printed circuit boards), a particularly critical issue is the separation of ink from the copper surface in areas where the ink is supposed to completely cover large copper surfaces, resulting in voids. This problem severely affects the electrical connectivity performance and reliability of the PCB, and also impacts its aesthetic quality. The formation of voids can not only lead to poor electrical conductivity but may also reduce the PCB’s durability and stability.

I. Specific Impacts

On the copper surface, the voiding issue—where ink coverage is incomplete—specifically manifests as tiny air bubbles or gaps forming between the ink layer and the copper substrate. These voids may occur individually or in dense clusters, seriously compromising the overall quality of the PCB. Not only do voids undermine the integrity of the ink layer, but they can also lead to poor electrical conductivity, signal transmission delays, or even signal interruptions, thereby affecting the performance and reliability of electronic products. Moreover, voids can serve as pathways for contaminants such as moisture and dust to penetrate the PCB, accelerating its aging and corrosion processes.

II. Cause Analysis

1. Poor pre-processing

Incomplete removal of the oxide layer: When copper surfaces are exposed to air for extended periods, a dense film of cuprous oxide forms. If this oxide layer is not effectively removed during the pre-treatment process, it will severely compromise the adhesion between the ink and the copper surface.

Oil Residue: Cutting fluids, cleaning agents, and other substances used during the manufacturing process may remain on the board surface. These oil residues can hinder the ink’s wetting and adhesion, leading to the formation of air bubbles.

2. Adhesion of impurities on the board surface

Insufficient environmental cleanliness: Tiny particles such as dust and fibers in the air within the printing workshop may adhere to the board surface, forming an isolating layer that hinders direct contact between the ink and the copper surface.

Improper handling: The gloves and clothing worn by operators may introduce impurities, or the surface of the board may become contaminated during handling and placement.

3. Copper surface quality issues

Improper copper surface roughness: Both excessively rough or overly smooth copper surfaces can affect the adhesion of the ink. A surface that is too rough will increase the gaps between the ink and the copper surface, while a surface that is too smooth may reduce the ink’s wettability.

Copper surface corrosion: Uneven or excessive corrosion can cause the copper surface to become uneven, affecting the uniformity of ink coverage.

4. Poor ink mixing

Improper formulation ratios: The proportions of each component in the ink directly affect its physical and chemical properties. An improper ratio can lead to changes in the ink’s viscosity, fluidity, curing speed, and other characteristics, thereby impacting print quality and adhesion.

Uneven Mixing: Insufficient mixing or improper mixing speed during the blending process can lead to uneven distribution of ink components, resulting in localized defects.

5. Uneven printing thickness

Uneven blade pressure: Uneven pressure distribution during the printing process can lead to inconsistent ink thickness. In areas where the pressure is too high, the ink may be squeezed too thinly, while in areas with insufficient pressure, the ink layer may become excessively thick.

Mismatch in printing speed: A mismatch between the printing speed and the ink’s fluidity can also lead to uneven ink thickness.

6. Impact damage

Mechanical Impact: During transportation, loading and unloading, or subsequent processing, the board surface may be subjected to mechanical impact, potentially damaging the ink layer.

Electrostatic discharge: Electrostatic discharge can generate instantaneous high temperatures and high voltages, which may damage the bond between the ink and the copper surface.

7. Baking issues

Improper temperature control: Uneven temperature distribution or excessive temperature fluctuations inside the oven can lead to uneven ink curing.

Insufficient or excessive curing time: If the curing time is too short, the ink may not fully cure; if it’s too long, it could lead to over-curing.

8. Repeated soldering or excessively high soldering temperature.

Interlayer stress in soldering: Repeated soldering operations can increase interlayer stress and reduce the bonding strength between the ink and the copper surface.

Excessive soldering temperature can damage the curing structure: High-temperature soldering may compromise the curing structure of the ink, causing the bond between the ink and the copper surface to become weak.

III. Conclusion

The issue of voids appearing in areas with full coverage on large copper surfaces in UV PCB ink is a complex and multifaceted challenge. Addressing this problem requires meticulous process control, the selection of high-quality raw materials, and stringent quality management. By continuously optimizing production processes, enhancing equipment precision, and strengthening employee training and standardized operations, we can effectively reduce the occurrence of voids, ensuring that the PCB’s electrical connectivity performance, durability, and aesthetic quality meet design specifications.

Disclaimer: The above content is sourced from the internet and is for reference only. If any infringement occurs, please contact us, and we will remove it promptly. 

Share to:

Related News


Analysis of Common Issues with UV PCB Ink (Part 1)

In the manufacturing process of PCBs (printed circuit boards), uneven UV PCB ink application is a common and serious issue. Specifically, the ink fails to adhere uniformly across the board surface, resulting in localized spots, streaks, or patches of white ink. In severe cases, this can even prevent the ink from being applied altogether. This phenomenon not only severely affects the visual quality of the PCB but also poses a potential threat to the electrical connectivity and stability of the circuit.


Detailed Explanation of Key Factors in Selecting UV PCB Ink Formulations (Part 2)

In the formulation design of UV PCB inks, in addition to pigments, binders, and photopolymerization initiators, the selection of curing agents, solvents, and additives, as well as the compatibility with the substrate material, are also crucial aspects that cannot be overlooked. The choice and combination of these components directly affect the ink’s curing speed, printing performance, and adhesion and durability on various substrates.


Detailed Explanation of the Key Factors in Selecting UV PCB Ink Formulations (Part 1)

As a core material in modern printing processes, UV PCB ink’s formulation design directly affects the color performance, durability, and overall quality of printed materials. In the ink formulation, pigments, binders, and photopolymerization initiators are the three key components; their selection and combination significantly influence the ink’s performance and application results.