Tel
Tel
+8618142863185
Follow us
Official Accounts
Official Accounts
- Top
Common Defects in UV 3D Printing: Prevention (Part 3)
Release time:
2026-08-06 06:49
Surface quality is one of the core advantages of UV‑based 3D printing, yet issues such as bubbles and pinholes, pronounced layer lines, and a sticky surface continue to occur frequently in practice. Bubbles and pinholes manifest as dense, tiny pits on or within the model’s surface, particularly noticeable with transparent resins; layer lines are the visible traces left by successive layers of cured material, becoming more pronounced when the layer thickness is set too high; and surface stickiness arises from the oxygen‑inhibited polymerization effect. These defects directly compromise both the visual appearance and the tactile experience of the printed part. Preventing surface‑quality‑related defects requires addressing three key areas: resin preparation, process parameter optimization, and equipment maintenance.
I. Resin Treatment and Bubble Prevention
Incomplete removal of entrapped air from the resin is the primary cause of bubbles. Pouring the resin too quickly or stirring too vigorously can both draw air into the resin, leading to bubble formation. To prevent bubbling, it is essential to standardize and strictly follow proper resin‑handling procedures.
When pouring the resin, proceed slowly to allow it to flow along the walls of the trough, avoiding direct impact that could create bubbles on the release film. Stir the resin gently, keeping the speed moderate. After pouring the resin into the trough, let it stand for 10–15 minutes to allow air bubbles to rise and escape naturally. In low‑temperature conditions, the resin’s viscosity increases and bubble‑removal slows; in such cases, extend the standing time as needed, or preheat the resin container in warm water before use.
Printing at excessively high speeds can also lead to bubble formation. When a model features fine structures—such as grooves, holes, or thin walls—the resin may not have enough time to fully fill these tiny spaces, trapping air that solidifies into bubbles. Preventive measures include reducing the print speed appropriately or orienting the model so that these delicate features face upward, allowing the resin sufficient time to flow and adequately fill the narrow areas.
Bubbles between the release film and the resin also require attention. When printing the first layer or after the build platform has descended, check whether the resin surface has fully covered the release film, ensuring that no bubbles remain.
II. Prevention of Layering
Excessive layer thickness is the primary cause of pronounced layer lines. The thicker each layer, the more pronounced the stair-stepping effect between layers, and the coarser the horizontal striations on the surface. To prevent layer‑line artifacts, it is essential to set the layer thickness parameter appropriately.
For models requiring high surface quality, it is recommended to use a smaller layer thickness. In areas with curved or inclined surfaces, a thinner layer can significantly reduce stair‑stepping artifacts, resulting in a smoother finish. Choosing the appropriate layer thickness involves balancing precision with print time—while thinner layers take longer to print, this extra time is well worth it for models with stringent aesthetic requirements.
Loose guide rails or unstable Z-axis motion can cause layer‑streaking defects. Regularly inspect the Z-axis guide rails for tightness, and tighten them promptly if any looseness is detected. Cleaning and lubricating the guide rail surfaces are equally important; maintaining the moving components in good condition ensures precise alignment between layers.
Printing at excessively high speeds can also lead to layer‑line artifacts. During rapid printing, the resin may not fully level and cure on each layer, resulting in uneven interlayer transitions. Reducing the print speed appropriately can help improve the quality of interlayer bonding.
III. Prevention of Surface Stickiness
The oxygen inhibition effect is the fundamental cause of surface tackiness. Oxygen in the air consumes the active free radicals generated during photopolymerization, thereby suppressing the polymerization reaction at the surface and resulting in incomplete curing. This effect is particularly pronounced when the coating is thin or when the curing energy is low.
Increasing air circulation can mitigate the effects of oxygen inhibition. Maintaining good airflow within the curing chamber helps remove oxygen near the surface, promoting more thorough surface curing. When feasible, inert gas can be introduced into the chamber to completely exclude oxygen, yielding even more desirable surface cure results.
Insufficient curing energy can also cause surface tackiness. Ensure adequate exposure time and that the light source is delivering normal power output. Different resins have varying requirements for curing energy; always set the exposure time according to the resin’s specifications. Post‑curing time should likewise be adjusted based on the resin type: for standard resins, a moderate duration is sufficient; for flexible resins, shorten the time to prevent excessive brittleness; and for transparent resins, extend the post‑curing period to maintain optimal clarity.
Before post‑curing, ensure that the model has been thoroughly cleaned and dried; otherwise, residual adhesive residues will cure on the surface, making subsequent removal more difficult. Cleaning should be performed using a two‑step process. For delicate models, an ultrasonic cleaner may be used as an aid, but the cleaning time should not be excessive to avoid damaging thin‑walled structures.
IV. Conclusion
Preventing surface‑quality defects requires a comprehensive approach that addresses resin handling, parameter settings, and equipment maintenance. In terms of resin handling, slow pouring, gentle stirring, and adequate settling to eliminate bubbles can effectively reduce bubble formation. For parameter settings, appropriately configuring layer thickness and print speed can mitigate layer‑line artifacts. As for equipment maintenance, regular inspections of the Z‑axis guide rails help ensure motion accuracy. To prevent surface tackiness, focus on controlling oxygen inhibition polymerization, ensuring sufficient curing energy, and standardizing post‑curing cleaning procedures. Before printing, it is recommended to establish a checklist: verify that the resin has been allowed to settle and degas fully, that layer thickness and exposure parameters meet the model’s specifications, that the Z‑axis guide rails are in proper condition, and that the post‑curing cleaning protocol is followed correctly. By implementing these systematic preventive measures, surface quality will be significantly improved, and the smoothness and fine detail of printed parts will better align with design expectations.
Disclaimer: The above content has been compiled from publicly available sources and is provided for reference only. If any infringement occurs, please contact us, and we will address it promptly.
Bossin Related Product Recommendations – 3D Printing | ||
Rigidity | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-100 | Bisphenol A epoxy acrylate | High hardness, high gloss, excellent chemical resistance, and rich body. |
B-113 | Bisphenol A epoxy acrylate | High hardness, high gloss, high fullness, contains 20% TPGDA. |
B-221 | Aliphatic polyurethane acrylate | Fast curing, resistant to boiling water |
B-276H | Aliphatic polyurethane acrylate | High hardness, fast curing, excellent toughness, and low yellowing. |
B-296 | Aliphatic polyurethane acrylate | Fast curing, chemical resistance, yellowing resistance, impact resistance |
B-296M | Polyurethane acrylate | Fast curing, resistant to polar solvents, yellowing-resistant, and impact-resistant. |
B-301 | Aromatic polyurethane acrylate | Fast curing, excellent toughness, and good sandability. |
B-302 | Aromatic polyurethane acrylate | Fast curing, high strength, excellent toughness, and good grindability. |
B-368 | Aliphatic polyurethane acrylate | Good toughness, excellent leveling, excellent bend resistance, and excellent heat resistance. |
B-529 | Polyester acrylate | Excellent adhesion, low shrinkage, and good resin compatibility. |
B-609 | Aliphatic polyurethane acrylate | Fast curing, high hardness, scratch resistance, and chemical resistance. |
Dentistry | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-100M | Bisphenol A epoxy acrylate | Low viscosity, high hardness, high gloss, and high body. |
B-113 | Bisphenol A epoxy acrylate | High hardness, high gloss, high fullness, contains 20% TPGDA. |
B-276H | Aliphatic polyurethane acrylate | High hardness, fast curing, excellent toughness, and low yellowing. |
B-296 | Aliphatic polyurethane acrylate | Fast curing, chemical resistance, yellowing resistance, impact resistance |
B-296M | Polyurethane acrylate | Fast curing, resistant to polar solvents, yellowing-resistant, and impact-resistant. |
B-301 | Aromatic polyurethane acrylate | Fast curing, excellent toughness, and good sandability. |
B-302 | Aromatic polyurethane acrylate | Fast curing, high strength, excellent toughness, and good grindability. |
B-368 | Aliphatic polyurethane acrylate | Good toughness, excellent leveling, excellent bend resistance, and excellent heat resistance. |
B-376 | Aliphatic polyurethane acrylate | LED yellowing is minimal, and the nail polish formulation exhibits excellent stability. |
B-609 | Aliphatic polyurethane acrylate | Fast curing, high hardness, scratch resistance, and chemical resistance. |
B-79D | Polyester acrylate | High hardness, low yellowing, and high evaporation efficiency at elevated temperatures. |
Casting | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-79D | Polyester acrylate | High hardness, low yellowing, and high evaporation efficiency at elevated temperatures. |
Resilience | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-210D | Aliphatic polyurethane acrylate | Fast curing, low heat of reaction, and excellent toughness. |
B-286 | Aliphatic polyurethane acrylate | Low heat generation, excellent toughness, wear resistance, and impact resistance. |
B-296M | Polyurethane acrylate | Fast curing, resistant to polar solvents, yellowing-resistant, and impact-resistant. |
Elasticity | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-268M | Aliphatic polyurethane acrylate | Good flexibility, excellent adhesion, superior plating performance, and strong hiding power. |
B-296 | Aliphatic polyurethane acrylate | Fast curing, chemical resistance, yellowing resistance, impact resistance |
B-39 | Aliphatic polyurethane acrylate | Low viscosity, good flexibility, and low volatility. |
B-450-2 | Aliphatic polyurethane acrylate | Low shrinkage upon curing, excellent flexibility, and good tensile strength and elasticity. |
B-451 | Aliphatic polyurethane methacrylate | Good stretchability, low shrinkage, and excellent flexibility. |
High transparency | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-296 | Aliphatic polyurethane acrylate | Fast curing, chemical resistance, yellowing resistance, impact resistance |
B-376 | Aliphatic polyurethane acrylate | LED yellowing is minimal, and the nail polish formulation exhibits excellent stability. |
Environmental protection | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-296SW | Aliphatic polyurethane acrylate | Yellowing resistance, impact resistance, bio-based content > 40% |
Monomer Recommendation | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
BM1211 (HPMA) | Hydroxypropyl methacrylate | HEMA-free, high strength, low irritation, and high adhesion |
BM2223 (TPGDA) | Di(propylene glycol) diacrylate | Good flexibility and low volatility |
BM3231 (TMPTA) | Trimethylolpropane triacrylate | High crosslink density, high hardness, high gloss, and excellent wear resistance. |
BM3235 (PET3A) | Pentaerythritol triacrylate | Fast curing, high crosslink density, high hardness, and chemical resistance. |
BM3380 (3EO-TMPTA) | Pentaerythritol triacrylate | More flexible and less irritating than TMPTA. |
Share to:
Related News