Tel
Tel
+8618142863185
Follow us
Official Accounts
Official Accounts
- Top
Common Defects in UV 3D Printing and How to Prevent Them (Part 2)
Release time:
2026-08-03 23:09
Interlayer adhesion defects are a critical issue in UV‑based 3D printing, significantly affecting the strength and integrity of printed models. Delamination—manifesting as cracks between layers or separation of upper and lower layers—and soft layers resulting from incomplete curing both lead to localized weakness. The root causes of interlayer adhesion problems span multiple factors, including exposure parameter settings, resin condition, equipment performance, and model design. To prevent such defects, it is essential to address four key areas: optimizing exposure parameters, managing resin quality, maintaining the printer, and refining the model’s structural design.
I. Proper Setting of Exposure Parameters
Insufficient interlayer curing is a major cause of delamination. If the resin in each layer does not fully cure within the exposure time, the chemical bonding between layers will be inadequate, resulting in insufficient interfacial adhesion. The key to preventing inadequate interlayer curing lies in appropriately setting both the single-layer exposure time and the bottom-layer exposure time.
The single-layer exposure time should be determined based on the resin type and layer thickness. If the exposure time is too short, the resin will fail to achieve sufficient crosslinking density, resulting in reduced interlayer adhesion. Different resins have varying requirements for exposure time; therefore, settings should follow the manufacturer’s recommended parameter ranges and be validated through test prints. The bottom-layer exposure time is equally critical—since the bottom layer serves as the foundation connecting the model to the build platform, insufficient exposure can lead to an unstable base, compromising the stable adhesion of subsequent layers and increasing the likelihood of delamination.
For high‑resolution models (over 10 cm), the exposure time per layer can be appropriately increased to enhance interlayer adhesion. During printing, the model is subjected to tensile forces as the release film is peeled away; therefore, the interlayer bond strength must be sufficient to withstand these repeated tensile loads.
II. Inspection and Maintenance of Release Film Condition
Excessive adhesion of the release film can lead to delamination. In equipment that employs a bottom‑up exposure process, each layer must be peeled off the release film after curing. If the release film’s adhesion is too strong, the tensile force generated during peeling may pull down or tear the previously cured underlying layer, resulting in interlayer separation.
To prevent issues related to release films, it is essential to regularly inspect their surface condition. Overuse can cause the film to wear down and become sticky; therefore, it should be replaced on a scheduled basis according to either the number of uses or the duration of service. If the surface exhibits scratches, dents, or noticeable signs of wear, replacement is also recommended without delay. Additionally, any contaminants on the release film should be cleaned regularly by gently wiping with a soft cloth and a dedicated cleaning agent, taking care to avoid scratching the film’s surface.
The tension state of the release liner also requires attention. When the film surface is slack or the tension is uneven, the peel force is distributed non-uniformly, which can easily lead to localized interlayer delamination. When installing a new liner, ensure that the tension is uniform.
III. Maintenance of Resin Condition
When resin degrades, expires, or becomes contaminated, its chemical reactivity decreases, preventing complete photopolymerization in certain areas and resulting in incomplete curing and insufficient interlayer adhesion.
Preventing resin‑related issues requires establishing standardized storage and usage procedures. Photopolymer resins should be stored in a cool, light‑protected, airtight environment, avoiding direct sunlight and high temperatures. The shelf life of resins is typically 6 to 12 months; any resin past its expiration date must undergo testing to confirm that its curing performance remains satisfactory before use.
During use, the resin should be kept clean to prevent contamination by dust, cured debris, and other impurities. When pouring the resin, proceed slowly to minimize bubble formation. If printing is not performed for an extended period, remove the resin from the reservoir and store it in a sealed container to prevent it from absorbing moisture from the air or undergoing partial pre‑polymerization.
IV. Optimization of Model Structure Design
An improperly designed model structure can lead to delamination. When the upper layers are large in volume and heavy, while the lower layers lack sufficient support or have an insufficient contact area, the print may delaminate and fracture at weak points due to uneven stress distribution.
Preventive measures include: evaluating interlayer stresses during the design phase and providing adequate support structures for overhanging areas; increasing the contact area between the model’s base and the build platform; and, for tall or thin-walled models, considering the addition of reinforcing ribs or adjusting the print orientation to reduce interlayer stresses. In slicing software, the settings for support density and contact point size should be optimized according to the model’s geometry, ensuring that supports effectively hold the part in place without imposing excessive load.
V. Conclusion
Preventing interlayer adhesion defects requires a comprehensive approach that addresses four key factors: exposure parameters, release film condition, resin management, and model design. Properly setting exposure parameters ensures complete curing of each layer; regular maintenance of the release film guarantees stable delamination; standardized resin‑state management preserves material activity; and optimized model geometry reduces interlayer stresses. Before printing, it is recommended to establish a checklist: verify that both single‑layer and bottom‑layer exposure times meet the resin’s specifications, inspect the release film’s surface condition and tension, confirm the resin is within its shelf life and free from contamination, and assess whether the model geometry requires additional support structures. By implementing these systematic preventive measures, interlayer adhesion defects can be effectively mitigated, leading to significantly improved structural integrity and mechanical performance of the printed part.
Disclaimer: The above content has been compiled from publicly available sources and is provided for reference only. If any infringement occurs, please contact us, and we will address it promptly.
Bossin Related Product Recommendations – 3D Printing | ||
Rigidity | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-100 | Bisphenol A epoxy acrylate | High hardness, high gloss, excellent chemical resistance, and rich body. |
B-113 | Bisphenol A epoxy acrylate | High hardness, high gloss, high fullness, containing 20% TPGDA. |
B-221 | Aliphatic polyurethane acrylate | Fast curing, resistant to boiling water |
B-276H | Aliphatic polyurethane acrylate | High hardness, fast curing, excellent toughness, and low yellowing. |
B-296 | Aliphatic polyurethane acrylate | Fast curing, chemical resistance, yellowing resistance, impact resistance |
B-296M | Polyurethane acrylate | Fast curing, resistant to polar solvents, yellowing-resistant, and impact-resistant. |
B-301 | Aromatic polyurethane acrylate | Fast curing, excellent toughness, and good sandability. |
B-302 | Aromatic polyurethane acrylate | Fast curing, high strength, excellent toughness, and good grindability. |
B-368 | Aliphatic polyurethane acrylate | Good toughness, excellent leveling, excellent bend resistance, and excellent heat resistance. |
B-529 | Polyester acrylate | Good adhesion, low shrinkage, and excellent resin compatibility. |
B-609 | Aliphatic polyurethane acrylate | Fast curing, high hardness, scratch resistance, and chemical resistance. |
Dentistry | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-100M | Bisphenol A epoxy acrylate | Low viscosity, high hardness, high gloss, and high fullness. |
B-113 | Bisphenol A epoxy acrylate | High hardness, high gloss, high fullness, containing 20% TPGDA. |
B-276H | Aliphatic polyurethane acrylate | High hardness, fast curing, excellent toughness, and low yellowing. |
B-296 | Aliphatic polyurethane acrylate | Fast curing, chemical resistance, yellowing resistance, impact resistance |
B-296M | Polyurethane acrylate | Fast curing, resistant to polar solvents, yellowing-resistant, and impact-resistant. |
B-301 | Aromatic polyurethane acrylate | Fast curing, excellent toughness, and good sandability. |
B-302 | Aromatic polyurethane acrylate | Fast curing, high strength, excellent toughness, and good grindability. |
B-368 | Aliphatic polyurethane acrylate | Good toughness, excellent leveling, excellent bend resistance, and excellent heat resistance. |
B-376 | Aliphatic polyurethane acrylate | LED yellowing is minimal, and the nail polish formulation exhibits excellent stability. |
B-609 | Aliphatic polyurethane acrylate | Fast curing, high hardness, scratch resistance, and chemical resistance. |
B-79D | Polyester acrylate | High hardness, low yellowing, and high evaporation efficiency at elevated temperatures. |
Casting | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-79D | Polyester acrylate | High hardness, low yellowing, and high evaporation efficiency at elevated temperatures. |
Resilience | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-210D | Aliphatic polyurethane acrylate | Fast curing, low heat of reaction, and excellent toughness. |
B-286 | Aliphatic polyurethane acrylate | Low heat generation, excellent toughness, wear resistance, and impact resistance. |
B-296M | Polyurethane acrylate | Fast curing, resistant to polar solvents, yellowing-resistant, and impact-resistant. |
Elasticity | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-268M | Aliphatic polyurethane acrylate | Good flexibility, excellent adhesion, superior plating performance, and strong hiding power. |
B-296 | Aliphatic polyurethane acrylate | Fast curing, chemical resistance, yellowing resistance, impact resistance |
B-39 | Aliphatic polyurethane acrylate | Low viscosity, good flexibility, and low volatility. |
B-450-2 | Aliphatic polyurethane acrylate | Low shrinkage upon curing, excellent flexibility, and good tensile strength and elasticity. |
B-451 | Aliphatic polyurethane methacrylate | Good stretchability, low shrinkage, and excellent flexibility. |
High transparency | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-296 | Aliphatic polyurethane acrylate | Fast curing, chemical resistance, yellowing resistance, impact resistance |
B-376 | Aliphatic polyurethane acrylate | LED yellowing is minimal, and the nail polish formulation exhibits excellent stability. |
Environmental protection | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-296SW | Aliphatic polyurethane acrylate | Yellowing resistance, impact resistance, bio-based content > 40% |
Monomer Recommendation | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
BM1211 (HPMA) | Hydroxypropyl methacrylate | HEMA-free, high strength, low irritation, and high adhesion |
BM2223 (TPGDA) | Dipropylene glycol diacrylate | Good flexibility and low volatility |
BM3231 (TMPTA) | Trimethylolpropane triacrylate | High crosslink density, high hardness, high gloss, and excellent wear resistance. |
BM3235 (PET3A) | Pentaerythritol triacrylate | Fast curing, high crosslink density, high hardness, and excellent chemical resistance. |
BM3380 (3EO-TMPTA) | Pentaerythritol triacrylate | More flexible and less irritating than TMPTA. |
Share to:
Related News