News

Knowledge

Company News

Application Mind Map

Test Report

Technical Article

Industry News

Solutions for Defects in UV Wood Coatings (Part 5)

Release time:

2026-03-18 23:31

Solutions for Defects in UV Wood Coatings (Part 5)

During the application of UV wood coatings, defects such as craters frequently occur, severely compromising product appearance and market competitiveness. Cratering manifests as circular depressions of varying sizes on the coating surface, with raised edges and potentially containing fine particles or contaminants at the center; these defects cannot be masked by subsequent coating applications. This paper addresses the issue of cratering by analyzing its root causes and proposing a series of specific remedial measures, while also briefly discussing preventive strategies.

I. Solutions to the Shrinkage Porosity Problem

1. Regulation of Surface Tension Differences

(1) Use of surfactants: During paint formulation, an appropriate amount of surfactant (such as a nonionic surfactant) should be added to reduce the overall surface tension of the coating, thereby better matching the surface tensions of the substrate and contaminants and minimizing cratering caused by surface tension mismatches. It is important to note that the dosage of the surfactant must be rigorously determined through experimentation; excessive addition may degrade the performance of the paint film.

(2) Coating formulation optimization: Adjust the resin-to-solvent ratio in the coating, select resins and solvents with low surface tension to fundamentally reduce the coating’s surface tension and thereby minimize the risk of cratering. At the same time, ensure compatibility among all coating components to prevent cratering caused by component incompatibility.

2. Control and Elimination of Pollution Sources

(1) Air Purification: Install a high-efficiency air purification system in the painting workshop, including oil mist collectors and dust filters, to ensure that the air quality in the workshop meets the requirements for painting operations. Regularly maintain and clean the air purification system to prevent it from becoming a new source of pollution.

(2) Substrate Cleaning: Prior to coating, the substrate must be thoroughly cleaned to remove release agents, oils, dust, and other contaminants from the surface. Methods such as solvent wiping, high-pressure air blowing, or ultrasonic cleaning may be employed to ensure the substrate surface is clean and free of contamination. In addition, the substrate should be dried to prevent moisture-induced craters.

(3) Compressed Air Purification: Thoroughly purify the compressed air used for spraying, including oil–water separation and drying. Install high-efficiency oil–water separators and air dryers to ensure that the compressed air is free of oil mist and moisture, thereby preventing these contaminants from entering the paint film and causing craters.

(4) Coating filtration: Prior to feeding the coating into the spray equipment, perform fine filtration to remove impurities and particulates. High-precision filter screens or filters may be used to ensure the coating remains pure and free from contamination. In addition, regularly clean the coating tanks and delivery pipelines to prevent contamination during storage and transport.

3. Selection and Adjustment of Coating Additives

(1) Selection of defoamer: Choose a defoamer that is compatible with the coating system to prevent cratering caused by incompatibility. At the same time, adjust the dosage of the defoamer based on the viscosity of the coating and the spraying process, ensuring that it effectively eliminates air bubbles without adversely affecting the performance of the paint film.

(2) Application of leveling agents: Adding an appropriate amount of leveling agent to the coating can enhance its leveling performance, enabling it to quickly form a smooth film surface after application. The selection of the leveling agent should be based on the type of coating and the coating process to ensure optimal performance.

II. Preventive Measures and Daily Management

1. Coating Environment Control

Maintain stable temperature in the paint booth to prevent changes in coating performance caused by temperature fluctuations. At the same time, keep the booth humidity within an appropriate range to avoid blistering or cratering of the paint film due to excessive humidity.

2. Equipment Maintenance and Cleaning

Regularly maintain and clean spray equipment, including the spray gun, paint tank, and delivery piping. Ensure that no residual paint or contaminants remain inside the equipment to prevent them from becoming sources of contamination. At the same time, inspect the equipment’s sealing performance to prevent air and impurities from entering the paint system.

3. Personnel Training and Operating Procedures

Provide specialized training for coating operators to enhance their operational skills and quality awareness. Ensure that operators are proficient in coating processes and equipment operating procedures, thereby preventing defects such as craters caused by improper operation. At the same time, establish stringent operating standards and inspection protocols, conducting quality inspections and maintaining detailed records for each process step.

III. Conclusion

The issue of cratering during the application of UV wood coatings is complex and challenging, requiring comprehensive, multi-faceted management. By controlling surface tension differentials, managing contamination sources, selecting appropriate coating additives, and strengthening preventive measures and routine operational controls, it is possible to effectively reduce the occurrence of defects such as cratering, thereby enhancing the coating quality and market competitiveness of UV wood coatings. In actual production, continuous lessons learned should be summarized, coating processes and equipment maintenance management systems should be continually optimized, and the stability and reliability of UV wood coating quality must be ensured.

Disclaimer: The above content is sourced from the internet and is provided for reference only. If any infringement occurs, please contact us, and we will remove it promptly.

Bossin Recommended Products – UV Wood Coatings
Putty primer
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-113	Bisphenol A epoxy acrylate	High hardness, high gloss, high fullness, contains 20% TPGDA
B-520	Polyester acrylate	Low viscosity, high gloss, excellent wettability, and cost-effective
B-522	Polyester acrylate	Low shrinkage, excellent flexibility, strong adhesion, and high cost-effectiveness.
Sanding primer
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-113	Bisphenol A epoxy acrylate	High hardness, high gloss, high fullness, contains 20% TPGDA
B-160D	Modified epoxy acrylate	Good flexibility, yellowing resistance, and excellent adhesion.
B-163	Modified epoxy acrylate	Good flexibility, excellent pigment wetting, and strong adhesion.
B-520	Polyester acrylate	Low viscosity, high gloss, excellent wettability, and cost-effective
B-522	Polyester acrylate	Low shrinkage, excellent flexibility, strong adhesion, and high cost-effectiveness.
Apply primer
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-02	Phosphate ester acrylate	Enhances adhesion to substrates such as metal, glass, and plastic.
B-05	Phosphate ester acrylate	Enhances adhesion to substrates such as metal, glass, and plastic.
B-113	Bisphenol A epoxy acrylate	High hardness, high gloss, high fullness, contains 20% TPGDA
B-165	Modified epoxy acrylate	Good flexibility and strong adhesion
B-522	Polyester acrylate	Low shrinkage, excellent flexibility, strong adhesion, and high cost-effectiveness.
B-535	Polyester acrylate	Excellent adhesion, rapid curing, good flexibility, and yellowing resistance.
B-546	Polyester acrylate	Good adhesion, fast curing, and excellent flexibility.
White primer
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-113	Bisphenol A epoxy acrylate	High hardness, high gloss, high fullness, contains 20% TPGDA
B-160D	Modified epoxy acrylate	Good flexibility, yellowing resistance, and excellent adhesion.
B-520	Polyester acrylate	Low viscosity, high gloss, excellent wettability, and cost-effective
B-522	Polyester acrylate	Low shrinkage, excellent flexibility, strong adhesion, and high cost-effectiveness.
B-529	Polyester acrylate	Good adhesion, low shrinkage, and excellent resin compatibility.
B-560	Polyester acrylate	Fast curing and excellent pigment wetting
Gloss topcoat
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-113	Bisphenol A epoxy acrylate	High hardness, high gloss, high fullness, contains 20% TPGDA
B-163	Modified epoxy acrylate	Good flexibility, excellent pigment wetting, and strong adhesion.
B-165	Modified epoxy acrylate	Good flexibility and strong adhesion
B-21C	Active amine photosensitizing promoter	Low color number, antioxidant and polymerization inhibitor, and enhanced curing rate
B-301	Aromatic Polyurethane Acrylate	Fast curing, good toughness, and excellent grindability.
B-302	Aromatic Polyurethane Acrylate	Fast curing, high strength, good toughness, and excellent grindability.
B-574C	Polyester acrylate	Low viscosity, low odor, excellent wettability; suitable for LED UV.
B-601	Aromatic Polyurethane Acrylate	High hardness, scratch resistance, chemical resistance, and excellent cost performance.
B-609	Aliphatic polyurethane acrylate	Fast curing, high hardness, scratch resistance, and chemical resistance.
B-868	Organosilicon UV-Curable Resin	Excellent leveling, smooth finish, fast curing, and stain resistance.
B-868H	Organosilicon UV-Curable Resin	Excellent leveling, smooth finish, fast curing, and stain resistance.
B-910A2	Aliphatic polyurethane acrylate	Low viscosity, yellowing resistance, chemical resistance, and steel-wool resistance.
B-912	Aliphatic polyurethane acrylate	Fast curing, high hardness, good toughness, and excellent chemical and wear resistance.
Matte topcoat
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-160D	Modified epoxy acrylate	Good flexibility, yellowing resistance, and excellent adhesion.
B-163	Modified epoxy acrylate	Good flexibility, excellent pigment wetting, and strong adhesion.
B-21C	Active amine photosensitizing promoter	Low color number, antioxidant and polymerization inhibitor, and enhanced curing rate
B-328M	Aliphatic polyurethane acrylate	Low gloss, low viscosity, excellent wettability, and a pleasant hand feel.
B-328R	Aliphatic polyurethane acrylate	Low gloss, excellent matting, good wetting, and a fine, smooth, and silky hand feel.
B-333	Aliphatic polyurethane acrylate	Low viscosity, excellent matting effect, good wetting properties, and excellent flexibility.
B-572	Polyester acrylate	Low viscosity, low odor, excellent wettability; suitable for LED UV.
B-650A	Aliphatic polyurethane acrylate	Low viscosity, excellent matting effect, fast curing, and good wettability.
B-868	Organosilicon UV-Curable Resin	Excellent leveling, smooth finish, fast curing, and stain resistance.
B-868H	Organosilicon UV-Curable Resin	Excellent leveling, smooth finish, fast curing, and stain resistance.
B-910A2	Aliphatic polyurethane acrylate	Low viscosity, yellowing resistance, chemical resistance, and steel-wool resistance.
B-912	Aliphatic polyurethane acrylate	Fast curing, high hardness, good toughness, and excellent chemical and wear resistance.
Bright White Finish
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-113	Bisphenol A epoxy acrylate	High hardness, high gloss, high fullness, contains 20% TPGDA
B-160D	Modified epoxy acrylate	Good flexibility, yellowing resistance, and excellent adhesion.
B-301	Aromatic Polyurethane Acrylate	Fast curing, good toughness, and excellent grindability.
B-302	Aromatic Polyurethane Acrylate	Fast curing, high strength, good toughness, and excellent grindability.
B-560	Polyester acrylate	Fast curing and excellent pigment wetting
B-574C	Polyester acrylate	Low viscosity, low odor, excellent wettability; suitable for LED UV.
B-601	Aromatic Polyurethane Acrylate	High hardness, scratch resistance, chemical resistance, and excellent cost performance.
B-868	Organosilicon UV-Curable Resin	Excellent leveling, smooth finish, fast curing, and stain resistance.
B-868H	Organosilicon UV-Curable Resin	Excellent leveling, smooth finish, fast curing, and stain resistance.
B-912	Aliphatic polyurethane acrylate	Fast curing, high hardness, good toughness, and excellent chemical and wear resistance.
Adherent
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-05	Phosphate ester acrylate	Enhances adhesion to substrates such as metal, glass, and plastic.
B-509B	Polyester acrylate	Good adhesion, good flexibility, and excellent pigment wetting.
B-531	Polyester acrylate	Good adhesion, impact resistance, excellent flexibility, and yellowing resistance.
B-535	Polyester acrylate	Excellent adhesion, rapid curing, good flexibility, and yellowing resistance.
B-546	Polyester acrylate	Good adhesion, fast curing, and excellent flexibility.
B-590	Polyester acrylate	Excellent adhesion, rapid curing, and good pigment wetting.
Filler type
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-113	Bisphenol A epoxy acrylate	High hardness, high gloss, high fullness, contains 20% TPGDA
B-520	Polyester acrylate	Low viscosity, high gloss, excellent wettability, and cost-effective
B-522	Polyester acrylate	Low shrinkage, excellent flexibility, strong adhesion, and high cost-effectiveness.
B-529	Polyester acrylate	Good adhesion, low shrinkage, and excellent resin compatibility.
Color correction
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-560	Polyester acrylate	Fast curing and excellent pigment wetting
Harden
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-113	Bisphenol A epoxy acrylate	High hardness, high gloss, high fullness, contains 20% TPGDA
B-301	Aromatic Polyurethane Acrylate	Fast curing, good toughness, and excellent grindability.
B-302	Aromatic Polyurethane Acrylate	Fast curing, high strength, good toughness, and excellent grindability.
B-560	Polyester acrylate	Fast curing and excellent pigment wetting
B-574C	Polyester acrylate	Low viscosity, low odor, excellent wettability; suitable for LED UV.
B-601	Aromatic Polyurethane Acrylate	High hardness, scratch resistance, chemical resistance, and excellent cost performance.
B-912	Aliphatic polyurethane acrylate	Fast curing, high hardness, good toughness, and excellent chemical and wear resistance.
Matte
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-328M	Aliphatic polyurethane acrylate	Low gloss, low viscosity, excellent wettability, and a pleasant hand feel.
B-328R	Aliphatic polyurethane acrylate	Low gloss, excellent matting, good wetting, and a fine, smooth, and silky hand feel.
B-329D	Aliphatic polyurethane acrylate	Low irritation, low viscosity, excellent wettability, and a pleasant feel.
B-333	Aliphatic polyurethane acrylate	Low viscosity, excellent matting effect, good wetting properties, and excellent flexibility.
B-650A	Aliphatic polyurethane acrylate	Low viscosity, excellent matting effect, fast curing, and good wettability.
Solid-color paint
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-519	Self-curing polyester acrylate	Self-initiated photopolymerization performance
B-530	Polyester acrylate	Low viscosity, excellent hydrophobicity, thixotropy, and improved ink misting
B-560	Polyester acrylate	Fast curing and excellent pigment wetting
Yellowing resistance
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-160D	Modified epoxy acrylate	Good flexibility, yellowing resistance, and excellent adhesion.
B-431	Cycloaliphatic Specialty Acrylates	Yellowing resistance, excellent wettability, low viscosity, and fast curing
Dip coating
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-160D	Modified epoxy acrylate	Good flexibility, yellowing resistance, and excellent adhesion.
Roll coating
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-100	Bisphenol A epoxy acrylate	High hardness, high gloss, excellent chemical resistance, and high fullness.
B-113	Bisphenol A epoxy acrylate	High hardness, high gloss, high fullness, contains 20% TPGDA
B-160D	Modified epoxy acrylate	Good flexibility, yellowing resistance, and excellent adhesion.
B-163	Modified epoxy acrylate	Good flexibility, excellent pigment wetting, and strong adhesion.
B-165	Modified epoxy acrylate	Good flexibility and strong adhesion
B-520	Polyester acrylate	Low viscosity, high gloss, excellent wettability, and cost-effective
B-522	Polyester acrylate	Low shrinkage, excellent flexibility, strong adhesion, and high cost-effectiveness.
Solvent-free spraying
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-251	Aromatic Polyurethane Acrylate	Fast curing, excellent flexibility, and good wetting of black ink pigments.
B-520	Polyester acrylate	Low viscosity, high gloss, excellent wettability, and cost-effective
B-574C	Polyester acrylate	Low viscosity, low odor, excellent wettability; suitable for LED UV.
LED-UV
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-113	Bisphenol A epoxy acrylate	High hardness, high gloss, high fullness, contains 20% TPGDA
B-21C	Active amine photosensitizing promoter	Low color number, antioxidant and polymerization inhibitor, and enhanced curing rate
B-27	Active amine photosensitizing promoter	Low color number, benzene-free, low odor, antioxidant and anti-polymerization
B-570	Polyester acrylate	Low viscosity, benzene-free, low odor, suitable for LED UV
B-574	Polyester acrylate	Benzene-free, low odor, and VOC levels meet cigarette pack standards.
B-574C	Polyester acrylate	Low viscosity, low odor, excellent wettability; suitable for LED UV.
Excimer lamp
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-241	Aliphatic polyurethane acrylate	Fast curing, excellent skin feel, and yellowing resistance.
Skin feel
Product Model/English Abbreviation	Product Name/Product Type	Product Features
B-113	Bisphenol A epoxy acrylate	High hardness, high gloss, high fullness, contains 20% TPGDA
B-165	Modified epoxy acrylate	Good flexibility and strong adhesion
B-241	Aliphatic polyurethane acrylate	Fast curing, excellent skin feel, and yellowing resistance.
B-328M	Aliphatic polyurethane acrylate	Low gloss, low viscosity, excellent wettability, and a pleasant hand feel.
B-328R	Aliphatic polyurethane acrylate	Low gloss, excellent matting, good wetting, and a fine, smooth, and silky hand feel.
B-574C	Polyester acrylate	Low viscosity, low odor, excellent wettability; suitable for LED UV.
B-868	Organosilicon UV-Curable Resin	Excellent leveling, smooth finish, fast curing, and stain resistance.
B-868H	Organosilicon UV-Curable Resin	Excellent leveling, smooth finish, fast curing, and stain resistance.
Single-item recommendation
Product Model/English Abbreviation	Product Name/Product Type	Product Features
BM2223 (TPGDA)	Di(propylene glycol) diacrylate	Good flexibility and low volatility
BM2224 (EO-HDDA)	Ethoxylated 1,6-hexanediol diacrylate	Good adhesion to plastics, good dilutability, and low volatility.
BM3231 (TMPTA)	Trimethylolpropane triacrylate	High crosslink density, high hardness, high gloss, and excellent wear resistance.
BM3235 (PET3A)	Pentaerythritol triacrylate	Fast curing, high crosslink density, high hardness, and excellent chemical resistance.
BM3380 (3EO-TMPTA)	Tripropylene Glycol Triacrylate	More flexible and less irritating than TMPTA.
BM6261 (DPHA-80)	Dipentaerythritol hexaacrylate	High crosslink density, high hardness, chemical and wear resistance, and water resistance.
BM6263 (DPHA-90)	Dipentaerythritol hexaacrylate	High crosslink density, high hardness, chemical and wear resistance, and water resistance.

Share to:

Solutions for Defects in UV Wood Coatings (Part 6)

Solutions for Defects in UV Wood Coatings (Part 4)