Overview of UV Epoxy Acrylates


The synthesis of epoxy acrylates was first reported as early as the 1950s; however, it was not until the 1970s that they began to be applied in the field of UV curing. Epoxy acrylates are produced by the esterification of commercially available epoxy resins with acrylic acid or methyl methacrylate. They currently represent the largest category of photopolymerizable oligomers consumed within China’s UV-curing industry. Based on their structural types, epoxy acrylates can be classified into: bisphenol A epoxy acrylates, phenolic epoxy acrylates, modified epoxy acrylates, and epoxidized oil acrylates.

1. Bisphenol A epoxy acrylate

The synthesis reaction equation for bisphenol A epoxy acrylate is shown below:

Bisphenol A-based epoxy acrylates contain aromatic rings and lateral hydroxyl groups in their molecular structure, which are conducive to enhancing adhesion; in contrast, aliphatic epoxy acrylates exhibit very poor adhesion. The aromatic ring structure also imparts higher rigidity, tensile strength, and thermal stability to the resin.

Such as B-100, B-100M, and B-120—physical property comparison:

  Viscosity
(cps/60℃)
Solid content
(wt%)
Acid value
(mg KOH/g)
Appearance
B-100 7000-10000 ≥98 ≤3.0 Light yellow and transparent
B-100M 4500–6500 ≥98 ≤3.0 Light yellow and transparent
B-120 3000-6000 ≥98 ≤2.0 Green and transparent

Advantages: The photopolymerization reaction rate is very fast; after curing, the material exhibits high hardness and tensile strength, a high-gloss film surface, and excellent resistance to chemical corrosion.

Drawbacks: The cured film lacks sufficient flexibility and exhibits high brittleness. After UV curing, the film layer still contains a relatively large number of residual acrylate groups. The polymerization reaction is “frozen” at a low conversion rate, resulting in the formation of a rigid cross-linked network structure. The remaining unreacted groups adversely affect the film’s resistance to aging and yellowing.

Solution: Add a large amount of reactive diluent to reduce viscosity, and minimize the use of highly functional “rigid” reactive diluents. For example: B-102 (add 15% TMPTA to B-100), B-102M (add 15% TMPTA to B-100M), B-105M (add 20% TPGDA to B-100M), B-123 (add 20% TPGDA to B-120).

2. Phenolic epoxy acrylate

The synthesis reaction equation for the phenol-epoxy acrylate reaction is as follows:

Phenolic epoxy resins are polyfunctional epoxy resins with a high benzene ring density, which endows them with characteristics of rigidity and high crosslinking degree. The resulting phenolic epoxy acrylates exhibit even higher reactivity, greater crosslinking density, and a densely packed aromatic ring structure within the crosslinked network, giving them exceptional thermal resistance. As such, they are often the preferred raw material for solder mask materials in the electronics industry and are widely used in PCB inks.

As with B-191 and B-192, a performance comparison between the two:

  Performance Comparison
B-191 Standard process: Viscosity gradually increases with storage time, so it must be used immediately. Storage stability is slightly poor.
B-192 Special processing ensures excellent storage stability and outstanding resistance to yellowing.

3. Modified epoxy acrylate

By chemically modifying epoxy acrylates as needed, it is possible to highlight certain performance advantages of the resin.

(1) Amine-modified epoxy acrylate

As is well known, organic amines serve as thermal crosslinking curing agents for epoxy resins. Primary and secondary amines can directly open the epoxy ring, becoming an integral part of the crosslinked epoxy polymer structure. Tertiary amines, on the other hand, merely catalyze the ring-opening reaction without themselves being covalently bonded to the crosslinked polymer chains; their reactivity is lower than that of the first two types of amines. Before adding acrylic acid, the epoxy resin is first heated and reacted with a small amount of aliphatic primary or secondary amine, allowing partial condensation between epoxy molecules and increasing the molecular weight of the resin while still retaining most of the epoxy groups. Subsequently, the resin is esterified with acrylic acid, yielding what is known as amine-modified epoxy acrylate. The primary purpose of this modification is to moderately increase the molecular weight during the reaction process, thereby enhancing the resin’s reactivity, reducing the shrinkage during curing, and improving adhesion and other performance characteristics.

Another implication of amine modification is the introduction of quaternary ammonium groups onto the resin. The charged core groups enhance the resin's wettability toward dust particles, which helps achieve a highly glossy cured surface and reduces surface curing defects. At the same time, this modification also improves adhesion to substrates that have undergone plasma treatment. The synthesis method is as follows: First, an epoxy resin is reacted with a sub-stoichiometric amount of acrylic acid under normal conditions. Once the acrylic acid has been completely converted and a small amount of residual epoxy groups remains, a calculated amount of tertiary amine and an acid are added to convert the residual epoxy groups into quaternary ammonium groups.

(2) Phosphoric (ester)-modified epoxy acrylate

Epoxy acrylates modified with phosphate (esters) are primarily designed to achieve excellent adhesion to metal substrates. The phosphate group induces slight corrosion on the metal substrate, forming a complex structure on the metal surface that enhances adhesion. A relatively simple synthesis method involves first reacting epoxy resin directly with an insufficient amount of acrylic acid; the residual epoxy groups then react with phosphoric acid to form phosphate esters. These phosphate esters can further react with another molecule’s epoxy group, thereby acting as chain extenders and yielding epoxy acrylates containing phosphonate groups within the polymer chain. Of course, the final product remains predominantly a mixture of esterification products. The reaction scheme below illustrates a representative structure of epoxy acrylates modified with phosphonate esters.

Alternatively, phosphorus oxychloride (POCl3) can be directly reacted with the lateral hydroxyl groups of epoxy acrylic resins, followed by hydrolysis to yield a modified resin grafted with phosphate groups. This method produces hydrochloric acid as a byproduct.

(3) Epoxy acrylate modified with polyfunctional anhydrides

Modifying epoxy acrylates with polyfunctional carboxylic anhydrides involves two main approaches: The first approach involves using anhydrides to extend the molecular chain of epoxy resins, thereby increasing their molecular weight, followed by acrylation. In this process, the anhydride groups become incorporated into the main chain of the prepolymers. The second approach entails reacting polyfunctional carboxylic anhydrides with the secondary hydroxyl groups in epoxy acrylates, introducing carboxyl groups onto the resin—a process known as carboxylation—where the anhydride groups are grafted onto the prepolymer chains. Commonly used polyfunctional carboxylic anhydrides include maleic anhydride, succinic anhydride, tetrahydrophthalic anhydride, hexahydrophthalic anhydride, methyl nadic anhydride, and trimellitic anhydride.

Anhydride chain extension is primarily aimed at enhancing the photoreactivity of oligomers and reducing the shrinkage during curing. It also helps to increase the heat distortion temperature of cured products. Resins modified with long-chain anhydrides (such as adipic acid) will also exhibit improved flexibility.

(4) Long-chain fatty acid-modified epoxy acrylate

By reacting epoxy groups with natural long-chain fatty acids such as ricinoleic acid, oleic acid, and linoleic acid, flexible long chains are introduced, thereby enhancing flexibility. At the same time, the resin’s wettability toward pigments and fillers may also be improved.

(5) Halogenated epoxy acrylate

Brominated epoxy acrylates can be obtained by reacting brominated bisphenol A epoxy resin with acrylic acid. When burned, they exhibit self-extinguishing properties and can be used as flame-retardant, light-curing materials. Fluorinated epoxy acrylates have a high refractive index (1.408–1.565) and are suitable for the manufacture of light-curing optical components.

The modified epoxy acrylates produced by Boxing Company mainly include B-151, B-153, and B-163. Comparison of Properties and Applications:

  Viscosity (cps/60℃) Performance Comparison
B-151 16,000–22,000 High viscosity, low halogen content, low yellowing, and high transparency; it exhibits greater flexibility, bend resistance, resistance to boiling water, and interlayer adhesion compared to B-100M.
B-153 4000-6000 High flexibility, good adhesion, and excellent pigment wetting properties.
B-163 1500-2500 Fast curing rate, excellent flexibility, and outstanding pigment wetting and dispersibility; boasts universal and good adhesion, high cost-effectiveness, and wide-ranging applications.

4. Epoxy oil acrylate

Many drying oils, such as soybean oil and flaxseed oil, contain a large number of C=C unsaturated double bonds. Under the action of peroxides, these double bonds are converted into epoxy groups. These oils themselves can be incorporated into cationic curing formulations to reduce viscosity and enhance flexibility. Alternatively, under the catalysis of zinc powder and hydrated zinc sulfide, epoxy oils can react with acrylic acid (as shown in the following equation), opening the epoxy ring to form acrylate esters of oxidized oils. The resulting products exhibit excellent flexibility and leveling properties, and notably possess outstanding wetting and dispersing capabilities for pigments. However, compared to bisphenol A epoxy acrylates, these resin systems have lower photo-reactivity and poorer mechanical properties in the cured films; thus, they are typically used as auxiliary resins in combination with other, more reactive resins.

 

Share to:

Related News


Introduction to Photoinitiators and Their Applications

A photoinitiator, also known as a photosensitizer or photocuring agent, is a class of compounds that can absorb energy at specific wavelengths in the ultraviolet (250–420 nm) or visible light (400–800 nm) range, generating free radicals, cations, and other species that initiate the polymerization, crosslinking, and curing of monomers.


Introduction to UV Adhesives and Their Applications

UV adhesive, also known as shadowless glue, photosensitive adhesive, or ultraviolet-curing adhesive, refers to a class of adhesives that can only cure when exposed to ultraviolet (UV) light. It can be used both as an adhesive itself and as a binder in paints, coatings, inks, and other similar products. "UV" is the abbreviation for "Ultraviolet Rays," which refers to ultraviolet light. Ultraviolet (UV) radiation is invisible to the naked eye and represents a portion of the electromagnetic spectrum lying beyond the visible light range, with wavelengths ranging from 10 to 400 nanometers. The curing mechanism of UV adhesives relies on photoinitiators (or photosensitizers) contained within the UV-curable material. When these photoinitiators absorb UV light, they generate active free radicals or cations, which in turn trigger polymerization, crosslinking, and branching chemical reactions. As a result, the adhesive transforms from a liquid state into a solid state within just a few seconds.


Introduction to Light-Curable Monomers and Their Applications

A monomer (also known as a "momer") is a general term for small molecules that can undergo polymerization either with identical or different types of molecules. It is a simple compound capable of undergoing polymerization reactions, condensation reactions, and other processes to form macromolecular compounds. Monomers serve as low-molecular-weight raw materials used in the synthesis of polymers.