Knowledge and Applications of UV Monomers


1

Overview

In the world of coatings and inks, traditional solvent-based formulations invariably come with a contingent of “organic sidekicks”—namely, organic solvents. Their primary function is to dissolve solid components and to adjust the overall viscosity of the system. However, these “sidekicks” do not take center stage in the film-forming process; instead, they quietly slip away behind the scenes, volatilizing into the atmosphere. As a result, they not only impose an environmental burden but may also pose certain safety risks.
In radiation-curing systems, because most of the UV resins used in the formulation have relatively high viscosities, solvents or diluents are typically added to adjust the viscosity. However, unlike the “organic accomplices” found in conventional solvent-borne coatings and inks, the diluents in radiation-curing systems generally participate in the curing and film-forming process and volatilize only minimally into the atmosphere during application. This inherent environmental advantage has earned radiation-curing systems a stellar reputation in the green coatings sector, making them true superstars of the industry.
Compared with organic solvents, these diluents that can participate in photopolymerization film-forming reactions are referred to as reactive diluents. They are small organic molecules containing polymerizable functional groups and are therefore commonly called monomers. In early photocuring systems, the reactive diluents used were typically conventional addition-polymerizable monomers, such as styrene, N-vinylpyrrolidone, methyl acrylate, and isooctyl acrylate. However, due to their low boiling points, strong odors, and high toxicity, these monomers are now rarely employed. Moreover, some monomers are highly viscous liquids or even solids at room temperature and thus lack any diluting effect; hence, it is more appropriate to classify them as monomers rather than reactive diluents.
Based on the number of reactive functional groups per molecule, monomers can be classified as monofunctional, difunctional, or polyfunctional. Monofunctional monomers are those in which each molecule contains only one functional group capable of participating in the curing reaction; common examples include hydroxyethyl methacrylate (HEMA), isobornyl acrylate (IBOA), and tetrahydrofurfuryl acrylate (THFA). Difunctional monomers contain two such functional groups per molecule, such as tripropylene glycol diacrylate (TPGDA) and 1,6-hexanediol diacrylate (HDDA). Polyfunctional monomers have three or more such functional groups per molecule, including trimethylolpropane triacrylate (TMPTA), pentaerythritol triacrylate, and propoxylated glycerol triacrylate. In theory, the greater the number of functional groups, the faster the curing rate, the better the film-forming properties, the higher the hardness, and the higher the crosslink density; at the same time, the molecular weight increases accordingly, intermolecular interactions become stronger, resulting in increased viscosity and reduced dilutability.
Based on the type of functional group, monomers can be classified into acrylate derivatives, methacrylate derivatives, vinyl compounds, vinyl ethers, epoxides, and others.
According to the curing mechanism, monomers can be classified into two categories: radical-type and cationic-type. Acrylates, methacrylates, and vinyl compounds belong to the radical type, while epoxides belong to the cationic type. Vinyl ethers, on the other hand, can participate in both radical polymerization and cationic polymerization, making them suitable as monomers for both types of photopolymerization systems.
Currently, whether it is UV coatings, UV inks, or UV adhesives, the predominant curing system is radical polymerization, and the monomers used in this system are mostly acrylates.

2

Single-functional UV monomer

Based on the number of reactive functional groups per molecule, UV monomers can be classified as monofunctional, difunctional, or polyfunctional. Today, we will focus on monofunctional UV monomers.
A monofunctional UV monomer is a compound that contains only one functional group per molecule capable of participating in the curing reaction. Common types of such functional groups include acrylates, methacrylates, vinyls, vinyl ethers, and epoxides.
Due to their low molecular weight, monofunctional UV monomers exhibit high volatility, leading to strong odors and significant irritation. Beyond these issues, what other characteristics do monofunctional UV monomers possess?
I. Low Viscosity
Most monofunctional UV monomers exhibit low viscosity, typically below 30 cP, thereby providing strong diluting power.
II. Slow Curing Rate
Because monofunctional UV monomers contain only a single photopolymerizable functional group, their photopolymerization rate is slow.
3. Low volumetric shrinkage upon curing
During free-radical addition polymerization, carbon–carbon double bonds are converted into single bonds, reducing the intermolecular spacing and increasing the density, which leads to volumetric shrinkage—much like water freezing into ice. Because monofunctional UV monomers have a low double-bond content, their volumetric shrinkage is relatively minor. This property makes such UV monomers well suited for applications that demand low shrinkage, such as UV adhesives.
IV. Low Crosslink Density
Because it contains only a single photopolymerizable functional group, monofunctional UV monomers do not form crosslinking points during radiation curing. Although this can enhance the flexibility of the cured film and reduce its brittleness, it also leads to a decrease in hardness, abrasion resistance, and solvent resistance. Therefore, monofunctional UV monomers are typically used in combination with polyfunctional UV resins and other UV monomers to maintain an adequate crosslinking density.
V. High Conversion Rate
Monofunctional UV monomers have low double-bond content, low viscosity, and readily undergo polymerization, resulting in high conversion rates.
The following introduces several common monofunctional UV monomers.
I. Methyl Acrylate/Butyl Acrylate Series
These monomers have low viscosity and excellent dilutability, and were once used as diluents in early UV-curable formulations; however, due to their high volatility, strong odor, and flammability, they are now largely no longer employed.
II. HEA/HEMA/HPA/HPMA
These four UV monomers contain hydroxyl groups, which help enhance adhesion to polar substrates.
Due to their relatively high irritancy, HEA and HPA may cause skin sensitization and eye irritation when used in high-temperature environments; therefore, they are generally not employed directly as reactive diluents in formulations but are instead utilized in the synthesis of polyurethane acrylates.
Hydroxyethyl methacrylate exhibits reduced odor and skin irritation due to the presence of an additional methyl group on the carbon atom of the double bond; however, its reactive activity is also diminished. Currently, HEMA and HPMA are widely used as reactive diluents in gel nail polishes.
III. IBOA/THFA/CTFA/PHEA
All four monomers possess a cyclic structure in their molecular architecture.
IBOA: Isobornyl acrylate
IBOA is a UV-curable monomer featuring a bicyclic isobornyl structure, characterized by a high boiling point, high glass transition temperature, and low shrinkage. It exhibits excellent adhesion to a wide range of substrates and delivers outstanding overall performance. Its sole drawback is a noticeable odor, which varies in acceptability among different users.
THFA: Tetrahydrofurfuryl acrylate
The THFA molecule contains a polar tetrahydrofuran ring, which exhibits some corrosivity toward substrates, particularly plastics, thereby enhancing adhesion. Due to its low Tg, the cured film tends to be relatively soft.
CTFA: Trimethylolpropane Triacrylate
CTFA is a rare monomer among monofunctional monomers that exhibits low odor and low irritancy, while providing moderate adhesion to most plastics and metals, excellent toughness, and outstanding wear resistance. It is thus a monomer with exceptionally well-rounded performance.
PHEA: 2-phenoxyethyl acrylate
PHEA is a low-viscosity monomer characterized by excellent dilutability, high reactivity, high refractive index, low shrinkage, and good flexibility. However, its inherent phenolic odor limits its use in formulations with stringent odor requirements.
IV. ACMO/DMAA
These two monomers belong to the acrylamide family.
ACMO: Acryloylmorpholine
ACMO is suitable for LED-UV curing, offering rapid curing, low odor, low irritation, low viscosity, and excellent dilutability. It reacts more quickly than conventional monofunctional monomers, resulting in a cured film that exhibits good flexibility while maintaining adequate hardness. Additionally, it is water-soluble and can be used in waterborne UV systems.
DMAA: N,N-Dimethylacrylamide
DMAA exhibits low viscosity and excellent UV resin dilution performance, with good adhesion to plastic and glass, high film hardness, and superior chemical resistance.
V. St/NVP
These two monomers belong to the vinyl monomer class.
St: Styrene
Styrene was initially used in combination with unsaturated polyesters in first-generation UV-curable wood coatings, owing to its low cost, low viscosity, and strong dilutability. However, due to its high volatility, strong odor, flammability, and significant toxicity, it is now rarely employed as a monomer.
NVP: N-Vinylpyrrolidone
NVP is characterized by low viscosity, low skin irritation, strong dilutability, and high reactivity; however, its strong odor and carcinogenicity have limited its application, and it is now rarely used in UV-curable formulations.

3

Dual-functional UV monomer

Difunctional UV monomers, as the name suggests, contain two reactive functional groups per molecule that can participate in curing reactions. These reactive groups can be acrylate or methacrylate types; however, acrylates currently dominate the market by a wide margin. Compared with their monofunctional counterparts, difunctional UV monomers not only cure more rapidly and exhibit significantly higher film-forming crosslink density, but also retain excellent dilutability. As the number of functional groups increases, the molecular weight rises accordingly, leading to a corresponding increase in viscosity; consequently, these monomers have lower volatility and a milder odor.
The following introduces several common difunctional UV monomers.
I. DPGDA/TPGDA
These two UV monomers are propylene glycol-based diacrylates.
DPGDA: Dipropylene glycol diacrylate.
DPGDA is characterized by low volatility, low viscosity, excellent dilutability, and rapid curing.
TPGDA: Tripropylene glycol diacrylate.
TPGDA contains one additional propoxy group compared with DPGDA, resulting in better flexibility, slightly lower viscosity, improved dilutability, faster curing, reduced skin irritation, and a lower price. It is currently the most widely used difunctional UV photoinitiator monomer.
II. HDDA
HDDA: 1,6-hexanediol diacrylate.
HDDA is renowned for its low viscosity, strong diluting power, and outstanding resin-solubilizing ability; it exhibits excellent adhesion to plastic substrates and can enhance the flexibility of the cured film. Compared with TPGDA, HDDA is more irritating to the skin and is also somewhat more expensive.
III. NPGDA/2PO-NPGDA
These two UV monomers are neopentyl glycol-based diacrylates.
NPGDA: Neopentyl glycol diacrylate.
NPGDA exhibits low viscosity, excellent dilutability, high reactivity, high Tg, and rapid curing; however, it is highly irritating to the skin.
2PO-NPGDA: Propoxylated neopentyl glycol diacrylate.
The introduction of propoxy groups reduces the skin irritation of NPGDA, while the cured film exhibits high tensile strength, excellent elongation, and low shrinkage.
IV. Ethoxylation of BPADA
Ethoxylated bisphenol A diacrylate, with main grades including 2EO-BPADA, 4EO-BPADA, and 10EO-BPADA.
By introducing ethoxy groups between the bisphenol A unit and the acrylate moiety, the resulting structure becomes similar to that of bisphenol A epoxy acrylate, both containing a bisphenol A framework. Consequently, these materials exhibit high hardness, high refractive index, excellent heat resistance, and superior chemical resistance.
Standard bisphenol A epoxy acrylate contains two bisphenol A units and exhibits a room-temperature viscosity on the order of tens of thousands of cP; in contrast, ethoxylated bisphenol A acrylate contains only one bisphenol A unit, with a room-temperature viscosity of just about 1,000 cP—significantly lower than that of the bisphenol A epoxy acrylate. Moreover, as the number of ethoxy groups increases, the viscosity decreases, while the flexibility and hydrophilicity of the cured film increase.
V. PEGDA
PEGDA: Polyethylene glycol diacrylate.
Based on molecular weight, PEGDA is classified into PEG(200)DA, PEG(400)DA, and PEG(600)DA. The cured films derived from these grades are relatively soft, exhibiting moderate tensile strength and elongation at break. As the molecular weight increases, both viscosity and flexibility rise, while the glass transition temperature (Tg) and skin irritation decrease, and hydrophilicity increases—truly a case of “the longer it gets, the gentler it becomes.”

4

Multi-functional UV monomer

Compared with monofunctional and difunctional UV monomers, polyfunctional UV monomers, although less dilutable, offer advantages such as low odor, low skin irritation, and rapid curing, thereby partially offsetting the shortcomings of monofunctional and difunctional UV monomers. Polyfunctional UV monomers are defined as those containing three or more reactive functional groups capable of participating in the curing reaction.

Due to the increased functional group content, polyfunctional UV monomers typically exhibit the following characteristics.
1. Low odor.
Due to their generally high molecular weight, polyfunctional UV monomers exhibit low volatility and minimal odor.
2. High viscosity and poor dilutability.
3. Fast curing speed.
Due to the presence of multiple functional groups, these UV monomers can rapidly undergo polymerization under UV irradiation to form a crosslinked network.
4. The cured film exhibits high hardness but significant brittleness.
This is because each molecule contains multiple reactive functional groups, resulting in a high crosslinking density in the photopolymerized product.
5. High curing shrinkage and poor adhesion to the substrate.
The following introduces several common polyfunctional UV monomers.

I. TMPTA Series.
TMPTA, trimethylolpropane triacrylate.
TMPTA features rapid curing, high gloss, high hardness, and high crosslinking density; however, the cured film is hard yet relatively brittle. With its low cost, it is currently the most widely used polyfunctional UV monomer.
TMPTMA, trimethylolpropane trimethacrylate.
Compared with TMPTA, TMPTMA has a slower curing rate due to the additional methyl group on its double bond; however, the cured film is harder and its viscosity is significantly lower than that of TMPTA.
3EO-TMPTA, 9EO-TMPTA, 15EO-TMPTA, ethoxylated trimethylolpropane triacrylate.
As the number of ethoxy groups increases, the cured film exhibits greater flexibility, reduced skin irritation, and enhanced water solubility. Effective December 1, 2023, the European Chemicals Agency has classified TMPTA as a Category 2 carcinogen. The urgent need to identify alternatives to TMPTA is now more pressing than ever, and ethoxylated TMPTA has emerged as one of the most promising substitutes.
3PO-TMPTA, propoxylated trimethylolpropane triacrylate.
Compared with ethoxylated TMPTA, propoxylated TMPTA not only enhances the flexibility of the cured film and reduces skin irritation, but also improves its water resistance due to the introduction of propoxy groups.

II. PET3A: Pentaerythritol triacrylate.

3. GPTA: Tripropylene Glycol Triacrylate.
GPTA features rapid curing, excellent flexibility, low irritancy, and superior pigment wetting.

IV. TH1ICTA: Tri(propenyl) isocitrate tri(2-hydroxyethyl) ester.
TH1ICTA is a white, waxy solid at room temperature, characterized by a high glass transition temperature, high reactivity, and excellent thermal stability. Its unique isocyanurate structure imparts outstanding wear resistance.

V. PET4A, pentaerythritol tetraacrylate.
PET4A cures faster, exhibits higher crosslink density, and achieves greater hardness than PET3A.

VI. Di-TMPTA: Bis(2-hydroxyethyl) trimethylolpropane tetraacrylate.
It exhibits high viscosity, rapid curing, and a high crosslinking density, resulting in a cured film that is hard yet not brittle, with excellent chemical resistance and wear resistance. In formulations, it is primarily used to enhance the photopolymerization rate and crosslinking density.

VII. DPHA: Pentaerythritol hexaacrylate.
High viscosity, high reactivity, high crosslink density, and high hardness; excellent wear resistance; commonly used in formulations designed to enhance hardness and wear resistance.

5

How to Choose the Right UV Monomer

In previous episodes of our UV monomer series, we covered the classification, key characteristics, and common types of UV monomers. Today, we’ll explore how to select the most suitable UV monomer for real-world project development.
In UV-curable formulation systems, in addition to UV resins and photoinitiators, UV monomers also play a crucial role. Beyond merely adjusting the viscosity of the system, UV monomers can impart or enhance various properties of the cured film, such as improving adhesion, enhancing flexibility, and increasing abrasion resistance. Therefore, the judicious selection and use of different monomers is an essential aspect of formulation design.
The selection of UV monomers should be made on a comprehensive basis, taking into account the specific application area of the development project, the type of substrate, and the required performance characteristics, with the aim of balancing all relevant requirements as much as possible and strategically combining different monomers to achieve optimal results. The following sections outline several key factors to consider when selecting UV monomers for practical applications.
I. Price
As photopolymerization technology continues to advance and the market becomes increasingly saturated, raw-material suppliers have proliferated like bamboo shoots after a spring rain, intensifying competition. In this environment, rapid capacity expansion has led to oversupply, fueling an escalating price war. The price of UV monomers directly influences their proportion in formulation systems, which in turn affects the selling price and profit margins of finished products—and ultimately their market competitiveness. In this year’s highly competitive, “involutionary” landscape, price has become the primary factor to consider when selecting UV monomers.
II. Odor and Irritancy
As public awareness of environmental protection continues to grow, demands for the odor and irritancy of formulated products are becoming increasingly stringent. Different UV monomers exhibit varying degrees of odor and irritancy due to their distinct chemical structures. In general, UV monomers with lower molecular weights tend to have stronger odors; however, this is not an absolute rule. The odor and irritancy of a UV monomer are primarily determined by its vapor pressure: the higher the vapor pressure, the more volatile the monomer. Once its concentration in the air reaches a certain level, it can cause discomfort or irritation to sensitive areas such as the skin and eyes.
Typically, the odor and irritancy of UV monomers follow this order: monofunctional > difunctional > polyfunctional.
During the production of UV monomers, process optimization—such as ethoxylation and propoxylation modifications—can reduce the odor and irritancy of the monomers.
Methacrylate monomers exhibit lower odor and irritancy than acrylate monomers; in applications with stringent requirements for odor and irritation—such as gel nail polish—HEMA and HPMA are typically chosen as reactive diluents.
III. Viscosity and Dilutability
The primary function of UV monomers in a formulation is to reduce system viscosity. If a particular UV monomer exhibits strong viscosity-reducing properties, its dosage in the formulation can be minimized, thereby maximizing the influence of the main component—UV resin—on the performance of the cured film. It should be noted, however, that low-viscosity monomers do not necessarily possess strong viscosity-reducing capabilities. Even for the same monomer, its diluting effectiveness can vary significantly across different formulation systems. High-viscosity monomers are generally not used primarily for viscosity reduction; instead, they are typically employed to enhance other properties of the cured film.
IV. Reactivity
Another function of UV monomers in a formulation is to influence the curing rate of the system. The higher the reactivity of a particular UV monomer, the greater its promoting effect on the overall curing of the formulation. It should be noted, however, that there is not a strictly linear relationship between the double-bond content of a UV monomer and its reactivity. Among the major functional-group classifications discussed in the previous video, (meth)acrylate monomers exhibit the highest reactivity, with acrylate monomers being more reactive than methacrylate monomers. This difference arises from the electronic effects and steric hindrance imposed by the methyl group attached to the double bond in methacrylates, which reduce their reactivity. Although monofunctional UV monomers polymerize at a slower rate, provided sufficient exposure to energy, their final conversion can often exceed 80–90%. In contrast, polyfunctional UV monomers may polymerize more rapidly under UV irradiation, but they can also leave behind a higher residual fraction of reactive groups.
V. Shrinkage Rate of Curing
Free-radical systems typically exhibit volumetric shrinkage during photopolymerization, as the conversion of double bonds to single bonds results in a net reduction in interatomic distances. In most applications, this shrinkage is undesirable. When coatings are cured on substrates such as metal, glass, and plastics, excessive shrinkage can lead to poor adhesion. For applications on flexible substrates—such as paper and thin films—shrinkage during curing can cause wrinkling or curling of the substrate.
The higher the functionality of a UV monomer, the more double bonds it contains for participation in the curing reaction, and the greater its shrinkage. In thermally cured formulations, the stresses generated during curing have sufficient time to dissipate, resulting in good adhesion. In contrast, photopolymerization proceeds much faster than thermal curing; the stresses developed during curing do not have enough time to relax, thereby compromising adhesion to the substrate.
VI. Surface Tension
Surface tension is a critical factor influencing the performance of photopolymerization systems. The wettability, adhesion, penetration, and leveling properties of coatings and inks are all closely related to surface tension. Liquids with low surface tension can wet and spread on surfaces with high surface energy; conversely, when the surface tension of a liquid exceeds the surface energy of the substrate, effective wetting and spreading cannot occur. Selecting monomers with appropriate surface tension as reactive diluents is one of the most effective strategies for tuning the surface tension of the system.
In practical applications, a comprehensive evaluation and analysis should be conducted based on the viscosity, curing rate, adhesion, and the physical and mechanical properties of the cured film required for the specific development project. If a single monomer cannot meet these requirements, two or more monomers with different functional groups should be selected and combined to formulate a photopolymerizable product with optimal overall performance.
Product Recommendations:

1. BM3231, trimethylolpropane triacrylate, abbreviated as TMPTA;

2. BM3380, ethoxylated trimethylolpropane triacrylate, abbreviated as 3EO-TMPTA

3. BM3235, pentaerythritol triacrylate, abbreviated as PET3A;

4. BM3384, propoxylated glycerol triacrylate, abbreviated as 3PO-GTA or GPTA;

5. BM6261 and BM6263 are dipentaerythritol hexaacrylates, abbreviated as DPHA; depending on the degree of esterification, the two grades are referred to as DPHA-80 and DPHA-90, respectively.

Share to:

Related News