Common Issues and Improvement Measures for UV Vacuum Plating


As an advanced surface treatment technology, UV vacuum plating is widely used in the manufacturing of various products due to its high efficiency and environmentally friendly characteristics. However, in actual production, issues such as iridescence, incomplete curing, coating delamination, orange-peel effect, particle formation, whitening and fogging, pinhole defects, and substrate etching often compromise product quality and appearance. The following sections will elaborate in detail on the causes of these problems and propose effective countermeasures.

I. The Rainbow Phenomenon

The occurrence of rainbow phenomena is often closely related to the non-uniformity of the topcoat curing process, the adhesion between the primer and the electroplated layer, contamination on the substrate surface, and the cleanliness of the coating delivery system. To reduce this phenomenon, one can appropriately lower the baking temperature of the topcoat or adjust the solubility of the solvent to match the curing speed of the topcoat; increase the infrared (IR) temperature to enhance the curing exposure energy of the primer; appropriately adjust the thickness of the primer film to avoid excessive stress; thoroughly inspect and clean the substrate to remove contaminants; clean the spray gun and air lines to ensure they are free from contamination; add an appropriate amount of additives or replace the coating to ensure its purity; and check the oil-water separator to guarantee that the compressed air remains free from contamination.

II. Poor Solidification

Poor curing can lead to incomplete coating curing, resulting in whitening or discoloration that severely affects the product’s appearance quality. Solutions include: adjusting the solvent evaporation rate, controlling the solvent composition, or using solvents with different evaporation rates; reducing the line speed to extend the coating’s exposure time under the UV lamp; adding an appropriate amount of thinner or reducing the spray flow rate to prevent the paint film from becoming too thick; promptly replacing aged UV lamps to ensure sufficient curing energy; adjusting the curing equipment parameters according to the workpiece; slowing down the conveyor belt speed to prolong the exposure time; and increasing the photopolymerization exposure energy and IR temperature to accelerate the curing process.

3. Coating peeling off

Coating delamination is typically caused by insufficient adhesion between the coating and the substrate. To address this issue, the following measures can be taken: thoroughly clean the substrate surface using ultrasonic cleaning or chemical treatments; select an appropriate coating that exhibits excellent adhesion based on the substrate material; optimize curing conditions, such as increasing the IR temperature, extending the leveling time, and reducing the film thickness; enhance the UV curing exposure energy, regularly inspect and replace aged UV lamps, and adjust the parameters of the UV curing equipment.

IV. Orange Peel Effect

The orange-peel effect can compromise the aesthetic appearance of a product as well as the adhesion and corrosion resistance of the coating. To address this issue, the following measures can be taken: thoroughly clean the substrate and enhance the wetting ability of the primer; select coatings with excellent leveling properties and avoid using high-viscosity coatings; adjust spray gun parameters and optimize spraying techniques to ensure uniform coating application; appropriately increase the IR temperature and extend the leveling time; reduce the coating viscosity by adding diluents or heating the coating; and moderately increase the coating thickness, while being careful to avoid other quality problems.

V. Granular Phenomenon

Particle formation is primarily caused by issues with the air purification system, inadequate substrate preparation, and the presence of particles in the coating material. To address these problems, the following countermeasures can be implemented: optimize the air purification system and perform regular maintenance and cleaning; thoroughly clean and pre-treat the substrate; use fine filtration for coatings, employing high-precision filter fabrics and replacing them regularly; precisely adjust the spray air pressure and establish operational guidelines; enhance the defoaming performance of the coating by adding an appropriate amount of defoaming agent; optimize the spraying environment by keeping it clean and controlling temperature and humidity; and perform regular maintenance and cleaning of the spraying equipment.

Six: Whitening and fogging

The phenomenon of whitening and fogging can severely affect product quality and aesthetic appeal. Improvement measures include: ensuring thorough curing of the primer, adjusting process parameters and checking the operational status of UV lamps; thickening the metal film layer, adjusting coating equipment parameters, and using high-quality coating materials; conducting dehumidification and drying treatments to reduce ambient humidity and performing regular maintenance on dehumidification equipment; and adjusting the solvent evaporation rate, modifying the solvent composition, and controlling spraying parameters.

7. Pinhole phenomenon

The pinhole phenomenon is characterized by the appearance of tiny holes on the coating surface, which compromise both the aesthetic appeal and protective performance of the coating. Countermeasures to address this issue include: controlling baking and leveling processes by increasing the IR temperature and extending the leveling time; managing film thickness by reducing the coating film’s thickness; treating the substrate surface to remove impurities; optimizing the coating formulation by selecting low-viscosity, highly fluid coatings and adding leveling agents and defoamers; and improving spraying techniques by using appropriate pressure and spray distance to avoid over-thick coatings.

8. Undercutting Phenomenon

The "biting" phenomenon can lead to defects such as an uneven coating surface, wrinkling, and peeling. Countermeasures to address this issue include: adjusting baking parameters by lowering the IR temperature and shortening the leveling time; optimizing production line speed to find the ideal setting; improving the substrate material and injection molding process by selecting higher-quality substrates and fine-tuning injection molding parameters; adjusting the coating and solvent formulations—choosing solvents with lower solubility for the primer or switching to a different coating formulation; and strengthening process monitoring and employee training to enhance operational skills.

9. Summary

In summary, by reasonably adjusting various process parameters and strictly controlling each stage of the coating process, we can effectively reduce the occurrence of common issues in UV vacuum plating, thereby enhancing product quality and market competitiveness. These measures not only help meet customer demands but also enable enterprises to gain a greater competitive edge in the fiercely competitive market.

Bossin Related Product Recommendations

UV plating

Product Model

Product Features

Application areas

B-165 (Modified Epoxy Acrylate)

Good flexibility and good adhesion

Vacuum-plated UV coatings, plastic UV varnishes

B-212A (aromatic polyurethane acrylate)

High cost performance, excellent plating properties, good toughness, and resistant to boiling water.

UV coatings, UV adhesives

B-221 (Aliphatic Polyurethane Acrylate)

Fast curing, resistant to boiling water

Vacuum-plated UV primer, plastic UV topcoat

B-268M (Aliphatic Polyurethane Acrylate)

Good flexibility, good adhesion, excellent plating performance, and strong covering power.

Vacuum-plated UV primer

B-6020 (Special Functional Group Acrylate)

Fast curing, excellent adhesion to metals and coatings, resistant to boiling water, good color development, and strong interlayer bonding.

Vacuum electroplating UV mid-coat

B-368 (Aliphatic Polyurethane Acrylate)

Fast curing, excellent toughness, good leveling, high fullness, excellent bend resistance, and good heat resistance.

Vacuum-plated UV coatings, plastic UV coatings, UV peelable adhesives

B-601 (Aromatic Polyurethane Acrylate)

Fast curing, high hardness, scratch-resistant, chemical-resistant, and cost-effective.

Wood UV Coating

B-609 (Aliphatic Polyurethane Acrylate)

Fast curing speed, solvent resistance, scratch resistance, high hardness, and cost-effectiveness.

Plastic UV coatings, vacuum-plated UV topcoats, metallic UV coatings, PVC surface gloss coatings, UV coatings for polishing and hardening wood flooring and cabinet panels, UV inks

B-919B (Aliphatic Polyurethane Acrylate)

Fast curing, high hardness, good toughness, chemical resistance, and wear resistance.

Vacuum-plated UV topcoat, metal/plastic/wood UV coatings

B-6019 (Acrylate with Special Functional Group)

Fast curing, excellent adhesion to metals and plastics, good leveling properties, excellent substrate wetting, resistant to boiling water, and excellent color development.

Vacuum-plated UV topcoat, plastic UV coating

Disclaimer: The above content is sourced from the internet and is for reference purposes only. If any infringement occurs, please contact us, and we will remove the content immediately. 

Share to:

Related News


Detailed explanation of the characteristics of traditional inks

In modern printing technology, ink serves as an essential medium for transferring images and text, and its performance directly affects the quality and visual appeal of printed materials. With the continuous advancement of printing technologies and the diversification of market demands, various types of inks have emerged, each possessing unique characteristics and advantages. This article will provide a detailed introduction to the features and applications of traditional inks such as volatile-drying inks, oxidative-polymerization inks, letterpress inks, offset inks, gravure inks, and screen-printing inks.


Types of UV Inks

UV inks, with their unique curing mechanism, outstanding printing performance, and wide range of applications, have become an important material in the modern printing industry. This article will classify and analyze UV inks from multiple perspectives and explore their applications in various fields.


Requirements for the Physical Performance Indicators of UV Inks

As an efficient and environmentally friendly printing material, UV ink occupies a crucial position in modern printing processes. Its physical performance indicators not only determine the visual appeal and durability of printed materials but also directly affect the stability and efficiency of the printing process. This article will comprehensively analyze the requirements for UV ink’s physical performance indicators from multiple perspectives.