Causes of Common Issues in UV Vacuum Plating (Part 2)


The UV vacuum plating process has gained a prominent position in surface treatment for various products thanks to its distinctive luster and excellent corrosion resistance. However, in actual production, surface defects often pose significant challenges for manufacturers, affecting the overall product quality and customer satisfaction. Defects such as pinholes, particles, and iridescence not only detract from the aesthetic appeal of the products but can also compromise their functional performance and durability. A thorough investigation into the causes of these defects is crucial for enhancing the quality of products produced using the UV vacuum plating process.

In the UV vacuum plating process, surface defects are one of the key factors affecting product quality. These defects may include pinholes, particles, and iridescence. The following is a detailed analysis of the causes of these defects and corresponding improvement measures:

I. Pinhole Phenomenon

1. Incomplete solvent evaporation: The solvent fails to fully evaporate within the paint film, forming bubbles that ultimately lead to pinholes.

(1) Improper solvent selection: Some solvents have poor volatility and tend to remain trapped within the paint film, forming bubbles.

(2) Insufficient curing conditions: The curing temperature, duration, or UV energy is inadequate, resulting in incomplete solvent evaporation.

2. Unclean substrate surface: Residual impurities on the substrate surface, such as oils and dust, can form pinholes during the coating process.

(1) Improper cleaning process: The substrate is not thoroughly cleaned, leaving behind residual impurities such as oils and dust.

(2) Secondary contamination: The substrate, after cleaning, becomes contaminated again during storage or transportation.

3. Excessive IR temperature after primer coating:

(1) Improper IR temperature setting: An excessively high IR temperature causes the solvent to evaporate rapidly, resulting in pinholes.

(2) Insufficient baking time: The IR baking time is too short, and the solvent has not had enough time to fully evaporate.

II. Granular Phenomenon

1. Compressed air and dust contamination in the environment: Dust and impurities in the air may adhere to the coating, forming particles.

(1) Unclean compressed air: Compressed air contains contaminants such as dust and a mixture of oil and water.

(2) Unclean painting environment: Excessive dust and insufficient air cleanliness in the painting workshop.

2. The substrate is not clean: Residual impurities on the substrate surface may form particles during the coating process.

(1) Inadequate substrate cleaning: Residual oil, dust, and other impurities remain.

(2) Surface scratches on the substrate: The substrate surface is scratched during processing or transportation.

3. Particles in the coating have not been fully filtered:

(1) Impurity Contamination: Particles may be inadvertently introduced into the coating during production or storage, and the coating is used directly without being filtered.

(2) Improper paint storage: During storage, paints may develop particles due to improper conditions such as temperature and humidity.

4. Incomplete defoaming of coatings: Bubbles in the coating may rupture during the application process, forming particles.

(1) Coating formulation issue: Insufficient or inappropriate use of defoaming agents in the coating formulation.

(2) Insufficient mixing: The coating failed to fully remove air bubbles during the mixing process.

III. The Rainbow Phenomenon

1. The primer is dissolved by the solvent in the topcoat:

The solvent in the topcoat may dissolve the undercoat that hasn't fully cured, causing relative movement within the coating layer and resulting in a rainbow effect.

(1) Incompatibility of primer and topcoat solvents: The solvent types of the primer and topcoat do not match, causing the primer to dissolve.

(2) Incomplete primer curing: The primer has not cured sufficiently and has failed to form a stable paint film.

2. Incomplete drying of the primer: Residual solvents remaining within the primer cause stress during the coating’s curing process, resulting in a rainbow effect.

(1) Insufficient curing conditions: The insufficient curing temperature, duration, or UV energy results in residual solvents remaining within the primer.

(2) Coating formulation issue: The solvent in the primer formulation evaporates too slowly.

3. Overly thick primer coat: An excessively thick primer coat may lead to incomplete internal drying, resulting in a rainbow effect.

(1) Improper coating process: During the coating process, the primer layer was applied too thickly, resulting in incomplete internal drying.

(2) Improper paint dilution ratio: The primer was diluted at too low a ratio, resulting in an excessively thick coating.

IV. Summary

In summary, surface defects in UV vacuum plating processes involve multiple factors, including solvent evaporation, substrate cleanliness, coating application techniques, and coating quality. To address these issues, we need to adopt a comprehensive approach from various angles. By optimizing solvent selection, enhancing substrate cleaning, improving coating application processes, and upgrading coating quality, we can effectively reduce the occurrence of defects such as pinholes, particles, and iridescence, thereby improving both the product quality and production efficiency of UV vacuum plating processes.

Disclaimer: The above content is sourced from the internet and is for reference only. If any infringement occurs, please contact us, and we will remove it promptly. 

Share to:

Related News


Causes of Common Issues in UV Vacuum Plating (Part 1)

In modern industrial manufacturing, the UV vacuum plating process—thanks to its high efficiency, environmental friendliness, and excellent decorative performance—is widely used in various fields such as automotive, electronics, and furniture. However, in actual production, poor adhesion and inadequate curing have become key factors that hinder the improvement of this process’s quality. Conducting an in-depth analysis of the specific causes behind poor adhesion and inadequate curing, and proposing effective countermeasures to address these issues, is of great significance for enhancing both the product quality and production efficiency of the UV vacuum plating process.


Application Fields of UV Vacuum Plating (Part 2)

As a shining gem in modern surface treatment technologies, UV vacuum plating technology—with its unique coating process and outstanding performance—is playing an increasingly important role across a wide range of industries. From the decorative finishing of home appliance casings to the protective treatments for aerospace equipment, from enhancing the performance of optical components to creating dazzling brilliance in jewelry and accessories, UV vacuum plating technology has become an indispensable part of numerous industries thanks to its broad application scope and remarkable results.


Application Fields of UV Vacuum Plating (Part 1)

With the rapid advancement of modern technology, UV vacuum plating—a cutting-edge surface treatment technique—has been widely adopted across numerous fields, significantly enhancing the quality and aesthetic appeal of products in various industries. In sectors such as construction, automotive, electronics, and medical devices, UV vacuum plating has become an indispensable process due to its outstanding wear resistance, corrosion resistance, and decorative effects.