Typical Issues in Dental UV 3D Printing (Part 6)


The aesthetic performance of dental restorations depends on the long-term color stability of the materials. After printing, UV‑cured resins do not maintain their original color and shape indefinitely. The chemical composition of the photopolymer formulation, storage conditions, and the length of time the printed part remains in place can all lead to changes in color and dimensional shrinkage or expansion. These factors directly affect the restoration’s esthetics and biocompatibility within the patient’s oral cavity.

I. Color‑changing tendency of resin formulations

The chemical composition of photosensitive resins is an intrinsic factor influencing color stability. Different formulations employ varying types of resin monomers, photoinitiators, and additives, resulting in differences in their resistance to discoloration. Studies have shown that certain formulations may exhibit color changes after curing or during prolonged storage, potentially attributable to residual photoinitiators, resin oxidation, or secondary reactions involving unreacted monomers.

In clinical practice, resin discoloration can result in a mismatch between the restoration and the adjacent teeth, compromising the overall esthetic outcome. This is particularly true for restorations in the anterior region, where color stability is of paramount importance.

II. The Influence of Storage Conditions on Material Stability

The condition of resin materials during storage directly affects the performance of printed parts. Photoinitiators in photopolymer resins are sensitive to ultraviolet light and heat, and improper storage conditions can accelerate resin degradation. Prolonged exposure to high temperatures or direct sunlight may induce slow pre‑polymerization, leading to changes in viscosity and a decline in print quality.

In addition to the resin itself, the printed model may also be affected by environmental factors during storage. When humidity is too high, the resin surface can absorb moisture, and temperature fluctuations may trigger the release of internal stresses within the material; both of these factors can accelerate discoloration or deformation.

III. Dimensional Drift Caused by Storage Time

Printed parts may undergo shrinkage and deformation as the storage time increases. After printing, photopolymer resins can still contain residual reactive functional groups that have not fully polymerized. Over time, these groups continue to undergo slow crosslinking reactions, leading to further volumetric shrinkage of the material.

Studies indicate that the directional offset of the implant analogs aligns with the model’s shrinkage direction. Starting from day 7, the three-dimensional deviation, linear distance deviation, and angular deviation of the analogs increase significantly. The decline in morphological stability may compromise the fit between the restoration and the model, leading to deviations during clinical placement.

IV. Preventive Measures Against Discoloration and Deformation

To minimize the impact of material stability and discoloration, preventive measures can be taken as follows: resin materials should be stored in a sealed container under light‑protected, low‑temperature conditions to avoid accelerated aging caused by high temperatures and direct sunlight; after printing, restorations should be fabricated and placed within the specified time frame to prevent loss of accuracy due to prolonged storage; for models intended for long-term storage, use sealed packaging or inert‑gas protection to reduce the influence of environmental factors.

V. Conclusion

Material stability and discoloration are critical issues in dental UV‑3D printing that affect the long-term performance of restorations. The chemical composition of the resin formulation determines its resistance to discoloration, while improper storage conditions can accelerate aging; over time, printed parts may undergo shrinkage and deformation. To mitigate these challenges, resins should be stored away from light and at low temperatures, and printed restorations should be placed in the patient’s mouth as soon as possible. During storage, environmental temperature and humidity must be carefully controlled. For anterior restorations—where aesthetics and fit are paramount—controlling the risk of discoloration is especially important. Implementing these measures requires establishing standardized protocols across multiple stages, including material management, post‑printing processing, and clinical scheduling.

Disclaimer: The above content has been compiled from publicly available sources and is provided for reference only. If any infringement occurs, please contact us, and we will address it promptly.

Bossin Related Product Recommendations – 3D Printing

Dentistry

Product Model/English Abbreviation

Product Name/Product Type

Product Features

B-100M

Bisphenol A epoxy acrylate

Low viscosity, high hardness, high gloss, and high body.

B-113

Bisphenol A epoxy acrylate

High hardness, high gloss, high fullness, containing 20% TPGDA.

B-276H

Aliphatic polyurethane acrylate

High hardness, fast curing, excellent toughness, and low yellowing.

B-296

Aliphatic polyurethane acrylate

Fast curing, chemical resistance, yellowing resistance, impact resistance

B-296M

Polyurethane acrylate

Fast curing, resistant to polar solvents, yellowing-resistant, and impact-resistant.

B-301

Aromatic polyurethane acrylate

Fast curing, excellent toughness, and good sandability.

B-302

Aromatic polyurethane acrylate

Fast curing, high strength, excellent toughness, and good grindability.

B-368

Aliphatic polyurethane acrylate

Good toughness, excellent leveling, excellent bend resistance, and excellent heat resistance.

B-376

Aliphatic polyurethane acrylate

LED yellowing is minimal, and the nail polish formulation exhibits excellent stability.

B-609

Aliphatic polyurethane acrylate

Fast curing, high hardness, scratch resistance, and chemical resistance.

B-79D

Polyester acrylate

High hardness, low yellowing, and high evaporation efficiency at elevated temperatures.

Monomer Recommendation

Product Model/English Abbreviation

Product Name/Product Type

Product Features

BM1211 (HPMA)

Hydroxypropyl methacrylate

HEMA-free, high strength, low irritation, and excellent adhesion

BM2223 (TPGDA)

Di(propylene glycol) diacrylate

Good flexibility and low volatility

BM3231 (TMPTA)

Trimethylolpropane triacrylate

High crosslink density, high hardness, high gloss, and excellent wear resistance.

BM3235 (PET3A)

Pentaerythritol triacrylate

Fast curing, high crosslink density, high hardness, and chemical resistance.

BM3380 (3EO-TMPTA)

Pentaerythritol triacrylate

More flexible and less irritating than TMPTA.

Share to:

Related News