Tel
Tel
+8618142863185
Follow us
Official Accounts
Official Accounts
- Top
Typical Issues in Dental UV 3D Printing (Part 4)
Release time:
2026-08-14 06:57
The chemical essence of light‑curing 3D printing lies in the polymerization of liquid resin under ultraviolet irradiation, resulting in a crosslinked polymer network. However, achieving complete conversion in practical applications is challenging. Some monomers fail to participate in the polymerization and remain in the cured material; these residual monomers may continuously leach from the printed part, triggering cytotoxic reactions. This issue is particularly critical in dental applications: restorations are in prolonged contact with oral mucosa and periodontal tissues, and any release of chemical substances can compromise the health of the local tissues. The adequacy of post‑curing treatment directly determines the level of residual monomers and the material’s biocompatibility.
I. Cytotoxicity Manifestations of Insufficient Post-Curing
The printed model is in a partially cured state, with the material still containing substantial amounts of unpolymerized monomers and oligomers. Without adequate post‑curing, these residual components will persist within the material. Studies have shown that uncured printing resins exhibit significant cytotoxicity toward oral cells; periodontal tissue cells display a marked reduction in cell viability upon exposure to extracts from insufficiently cured materials.
In practice, some operators, due to time constraints or by neglecting the post‑curing step, proceed directly to clinical use after only brief light curing. Under such conditions, residual monomers continue to leach into the oral environment, potentially triggering chronic inflammatory responses in the local tissues.
II. Effect of Post-Curing Time on Cell Viability
Post‑curing time and washing time both have a significant impact on cell viability. Extending the washing duration removes a greater proportion of uncured resin monomers remaining on the surface, thereby reducing their contact with biological tissues. Conversely, prolonging the post‑curing period allows the polymerization reaction within the material to proceed further, increasing crosslink density and concomitantly lowering the residual monomer content. The combined effect of these two factors enhances the material’s cellular compatibility.
However, even when post‑curing is performed according to the manufacturer’s recommended standard protocol, cytotoxicity is reduced but not completely eliminated. This suggests that the manufacturer’s recommended post‑curing parameters may be relatively conservative; for specific clinical applications, it may be necessary to extend the post‑curing time appropriately to achieve a higher level of biocompatibility.
III. Detection of Residual Monomers and Their Clinical Significance
The polymerization conversion rate of resins varies considerably, and the curing efficiency differs among various formulation systems. The types and concentrations of residual monomers directly affect the biocompatibility of the material. Certain monomers have been shown to exhibit cytotoxicity or sensitizing properties, so their residual levels in the material must be kept within safe limits.
Although relevant standards impose clear requirements for biocompatibility testing of dental materials, the degree of curing in 3D‑printed materials is heavily influenced by printing parameters and post‑processing conditions, necessitating continuous monitoring of batch-to-batch consistency.
IV. Directions for Optimizing the Post-Curing Process
To mitigate the risk of residual monomers, the post‑curing process can be optimized in the following ways: select appropriate post‑curing time and temperature based on the resin type, as post‑curing conditions vary across different resin systems; employ multi‑directional irradiation to ensure uniform curing of complex‑shaped surfaces; thoroughly clean the surface prior to curing to remove uncured resin; and regularly calibrate the light intensity of the curing chamber to maintain stable energy output.
V. Conclusion
Incomplete curing and the risk of residual monomers are core biosecurity concerns in dental UV‑based 3D printing. Print resins that have not undergone adequate post‑curing exhibit significant cytotoxicity toward oral cells, and extending both the post‑curing time and the rinsing duration can enhance the material’s cellular compatibility. However, even when following the manufacturer’s recommended procedures, cytotoxicity may not be fully eliminated. In practical applications, it is essential to optimize the post‑curing protocol—beyond the manufacturer’s default settings—based on the specific material properties and clinical use case, in order to minimize the risk of residual monomers as much as possible. For restorations intended for prolonged contact with the oral mucosa, biosecurity validation should be integrated throughout the entire process, from material selection and printing parameter optimization to post‑processing refinement.
Disclaimer: The above content has been compiled from publicly available sources and is provided for reference only. If any infringement occurs, please contact us, and we will address it promptly.
Bossin Related Product Recommendations – 3D Printing | ||
Dentistry | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-100M | Bisphenol A epoxy acrylate | Low viscosity, high hardness, high gloss, and high body. |
B-113 | Bisphenol A epoxy acrylate | High hardness, high gloss, high fullness, contains 20% TPGDA. |
B-276H | Aliphatic polyurethane acrylate | High hardness, fast curing, excellent toughness, and low yellowing. |
B-296 | Aliphatic polyurethane acrylate | Fast curing, chemical resistance, yellowing resistance, impact resistance |
B-296M | Polyurethane acrylate | Fast curing, resistant to polar solvents, yellowing-resistant, and impact-resistant. |
B-301 | Aromatic polyurethane acrylate | Fast curing, excellent toughness, and good sandability. |
B-302 | Aromatic polyurethane acrylate | Fast curing, high strength, excellent toughness, and good grindability. |
B-368 | Aliphatic polyurethane acrylate | Good toughness, excellent leveling, excellent bend resistance, and excellent heat resistance. |
B-376 | Aliphatic polyurethane acrylate | LED yellowing is minimal, and the nail polish formulation exhibits excellent stability. |
B-609 | Aliphatic polyurethane acrylate | Fast curing, high hardness, scratch resistance, and chemical resistance. |
B-79D | Polyester acrylate | High hardness, low yellowing, and high evaporation efficiency at elevated temperatures. |
Monomer Recommendation | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
BM1211 (HPMA) | Hydroxypropyl methacrylate | HEMA-free, high strength, low irritation, and excellent adhesion |
BM2223 (TPGDA) | Di(propylene glycol) diacrylate | Good flexibility and low volatility |
BM3231 (TMPTA) | Trimethylolpropane triacrylate | High crosslink density, high hardness, high gloss, and excellent wear resistance. |
BM3235 (PET3A) | Pentaerythritol triacrylate | Fast curing, high crosslink density, high hardness, and chemical resistance. |
BM3380 (3EO-TMPTA) | Pentaerythritol triacrylate | More flexible and less irritating than TMPTA. |
Share to:
Related News