Tel
Tel
+8618142863185
Follow us
Official Accounts
Official Accounts
- Top
Disadvantages of Dental UV 3D Printing
Release time:
2026-08-12 07:11
The application of UV‑3D printing technology in dentistry is steadily expanding, yet its limitations warrant close attention. From the choice of printing materials to the stability of the final products, and from mechanical properties to biocompatibility, this technology continues to face challenges at multiple stages. These shortcomings are evident both in the performance gaps compared with methods such as milling and conventional casting, and in the potential impact of post‑processing steps on dimensional accuracy.
I. Insufficient Mechanical Properties
Compared with CAD/CAM-milled composite resin blocks, light-cured 3D-printed resins exhibit significant differences in mechanical properties. Studies have shown that the flexural strength, surface hardness, and elastic modulus of printed resins are all lower than those of milled materials; similar findings have also been reported in research on denture base materials.
Printing methods and process parameters significantly influence mechanical properties. At different build orientations, the material exhibits variations in flexural strength and wear resistance. Although post‑curing can partially enhance mechanical performance, the overall properties still fall short of those achieved with conventionally manufactured materials. Moreover, the surface hardness and wear resistance of some printed parts remain inferior to those obtained via traditional fabrication techniques.
II. Dimensional Stability Issues
Shrinkage during post‑curing is the primary factor affecting the dimensional accuracy of dental UV‑based 3D printing. Studies have shown that post‑curing induces dimensional deviations in surgical guides, which differ from those of the uncured control group. This shrinkage arises from additional crosslinking reactions during the polymerization process and may compromise the precision required in applications such as surgical guides and implant models.
The duration of storage also affects the dimensional stability of resin models. As storage time increases, photopolymer resin dental arch models exhibit progressively greater shrinkage and deformation, with the posterior arch width potentially contracting beyond clinically acceptable tolerances. Stability varies among different materials, so time‑related limitations should be carefully considered prior to use.
III. Biocompatibility Risks
Unfully cured photopolymer resins pose a cytotoxic risk to oral tissues. Studies have demonstrated that uncured printed resins exhibit significant cytotoxicity toward periodontal ligament fibroblasts. Even after post‑curing as recommended by the manufacturer, cytotoxicity is reduced but not entirely eliminated. While some materials are safe under short‑term exposure, prolonged use may still elicit cellular responses.
The release of residual monomers is a critical factor affecting biocompatibility, as unpolymerized monomers may continue to leach in the oral environment. Furthermore, certain light‑cured resins can generate toxic byproducts during manufacturing, resulting in relatively high operational risks.
IV. Color Stability and Surface Properties
3D-printed denture base resins exhibit poor color stability. Studies have shown that these printed resins are highly sensitive to color changes and may discolor over prolonged use. Furthermore, the surfaces of printed resins tend to promote microbial adhesion more readily than those of conventionally milled materials, potentially increasing the risk of plaque accumulation.
Surface roughness directly affects the aesthetics and cleanability of restorations. Although polishing can enhance surface quality, the layer‑by‑layer structure inherent to printed parts may complicate post‑processing.
V. Cost Issues Related to Materials and Equipment
The high equipment costs associated with certain printing processes limit their widespread clinical adoption. Although photosensitive resins are moderately priced, the overall cost of specialized resin materials remains higher than that of conventional dental materials. 3D-printed indirect bonding trays exhibit certain limitations in bracket‑placement accuracy, and angular control still requires improvement.
VI. Uncertainty in Clinical Application
Currently, long-term clinical data on 3D‑printed dental resins remain limited, and the long-term clinical performance and durability of these materials have not been fully validated. Therefore, their use should be approached with caution, particularly in applications—such as long‑term restorations—that demand high durability. The flexural strength of 3D‑printed occlusal splints is lower than that of milled resins, and they are more susceptible to aging and water absorption.
VII. Conclusion
The main drawbacks of dental UV‑3D printing include insufficient mechanical properties, issues with dimensional stability, potential biocompatibility concerns, suboptimal color and surface characteristics, and a limited body of clinical data. The overall mechanical performance of printed resins falls short of that of milled materials; post‑curing shrinkage and extended curing times can compromise model accuracy; the cytotoxicity of residual monomers must be mitigated through optimized post‑processing protocols; color stability and susceptibility to microbial adhesion lag behind those of milled materials; and evidence regarding long‑term clinical outcomes remains inadequate. These limitations underscore the need for careful, scenario‑specific selection when applying UV‑3D printing in dentistry—particularly in high‑demand applications such as long‑term restorations—where integration with conventional techniques or further technological maturation is still required.
Disclaimer: The above content has been compiled from publicly available sources and is provided for reference only. If any infringement occurs, please contact us, and we will address it promptly.
Bossin Related Product Recommendations – 3D Printing | ||
Dentistry | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
B-100M | Bisphenol A epoxy acrylate | Low viscosity, high hardness, high gloss, and high body. |
B-113 | Bisphenol A epoxy acrylate | High hardness, high gloss, high fullness, containing 20% TPGDA. |
B-276H | Aliphatic polyurethane acrylate | High hardness, fast curing, excellent toughness, and low yellowing. |
B-296 | Aliphatic polyurethane acrylate | Fast curing, chemical resistance, yellowing resistance, impact resistance |
B-296M | Polyurethane acrylate | Fast curing, resistant to polar solvents, yellowing-resistant, and impact-resistant. |
B-301 | Aromatic polyurethane acrylate | Fast curing, excellent toughness, and good sandability. |
B-302 | Aromatic polyurethane acrylate | Fast curing, high strength, excellent toughness, and good grindability. |
B-368 | Aliphatic polyurethane acrylate | Good toughness, excellent leveling, excellent bend resistance, and excellent heat resistance. |
B-376 | Aliphatic polyurethane acrylate | LED yellowing is minimal, and the nail polish formulation exhibits excellent stability. |
B-609 | Aliphatic polyurethane acrylate | Fast curing, high hardness, scratch resistance, and chemical resistance. |
B-79D | Polyester acrylate | High hardness, low yellowing, and high evaporation efficiency at elevated temperatures. |
Monomer Recommendation | ||
Product Model/English Abbreviation | Product Name/Product Type | Product Features |
BM1211 (HPMA) | Hydroxypropyl methacrylate | HEMA-free, high strength, low irritation, and excellent adhesion |
BM2223 (TPGDA) | Di(propylene glycol) diacrylate | Good flexibility and low volatility |
BM3231 (TMPTA) | Trimethylolpropane triacrylate | High crosslink density, high hardness, high gloss, and excellent wear resistance. |
BM3235 (PET3A) | Pentaerythritol triacrylate | Fast curing, high crosslink density, high hardness, and chemical resistance. |
BM3380 (3EO-TMPTA) | Pentaerythritol triacrylate | More flexible and less irritating than TMPTA. |
Share to:
Related News