A Brief Discussion on the Influence of Temperature on UV Resin Synthesis and Its Control


I. What is temperature?

Temperature is a physical quantity that indicates the degree of hotness or coldness of an object. On a microscopic level, it reflects the intensity of thermal motion of the object's molecules. The faster the molecules in an object move, the higher its temperature.

II. How temperature is expressed

Temperature can only be measured indirectly through certain properties of an object that change with temperature; the scale used to quantify the numerical value of an object’s temperature is called a thermometer scale.

The international unit is the thermodynamic temperature scale (K). Currently, other temperature scales widely used internationally include the Fahrenheit scale (°F), the Celsius scale (°C), and the International Practical Temperature Scale. In addition, there are also the Réaumur scale and the Rankine scale.

The relationship between Celsius and Fahrenheit temperatures:

T℉ = 1.8t℃ + 32 (where t is the temperature in Celsius and T is the temperature in Fahrenheit)

The relationship between Celsius temperature and Kelvin temperature:

°K = ℃ + 273.15

The relationship between Celsius temperature and Fahrenheit temperature:

oR = ℃ / 1.25

The relationship between Celsius temperature and Rankine temperature:

R = ℃ + 491.67

Temperatures under different temperature scales:

Temperature scale Absolute zero The freezing point of water at standard atmospheric pressure. Normal human body temperature The boiling point of water at standard atmospheric pressure.
Kelvin scale 0.00K 273.15 K 309.95K 373.15K
Celsius scale -273.15℃ 0.00℃ 36.80℃ 100.00℃
Fahrenheit scale -459.67°F 32.00°F 98.24°F 211.97°F
Celsius scale -218.52°Ré 0.00°Ré 29.44°Ré 80.00°Ré
Rankine scale 0.00R 491.67R 557.91R 671.641R

III. The Zeroth Law of Thermodynamics

IV. Methods for Measuring Temperature

Contact temperature measurement; non-contact temperature measurement; other measurement parameters.

1. Contact Temperature Measurement Method

The temperature-sensing element is in direct contact with the object being measured, allowing for sufficient heat exchange between the two. Eventually, thermal equilibrium is reached, at which point a certain physical parameter of the temperature-sensing element reflects the temperature value of the object being measured.

2. Non-contact temperature measurement method

The temperature-sensing element does not come into contact with the object being measured; instead, it exchanges heat via radiation. Therefore, it can avoid the drawbacks of contact-based temperature measurement methods and boasts a higher upper temperature limit.

3. Other measurement indicators

Based on the different effects of temperature on the human body, the following measurement indicators can be further categorized:

Dry-bulb temperature The reading obtained from a dry-bulb thermometer exposed to air but not directly exposed to sunlight.
Wet-bulb temperature The air temperature at which water vapor in the air reaches saturation under isenthalpic air conditions.
Equivalent temperature The ratio of the enthalpy to the specific heat of moist air.
Empathic temperature A chart for calculating perceived temperature based on subjects’ sensory perceptions of the environment, derived through experimentation.
Catatonic Using a simulation approach, we measured the impact of environmental factors on the intensity of heat dissipation from the human body.

V. The Influence of Temperature on Organic Synthesis

The effect of temperature on the synthesis process; the effect of temperature on the catalyst; the effect of temperature on the polymerization inhibitor.

1. The effect of temperature on the synthesis process

Example 1: Synthesis of Standard Epoxy Acrylate

Change in reaction endpoint time at different temperatures:

Example 2: Synthesis of Polyurethane Acrylate

Reaction time for the second step varies at different temperatures:

Conclusion: In organic synthesis, the higher the temperature, the faster the reaction rate.

2. The effect of temperature on catalysts

Example 1: The reaction of the catalyst triphenylphosphine in propylene acrylate, with the addition amount and temperature change rate shown in the figure below:

Example 2: The reaction of dibutyltin dilaurate catalyst in polyurethane acrylate, with the addition amount and temperature change rate shown in the figure below:

Conclusion: The more catalyst added, the faster the reaction temperature rises; conversely, the higher the temperature, the better the catalytic effect.

3. The effect of temperature on the polymerization inhibitor

In the acrylic resin synthesis experiment, since there are double bonds, a polymerization inhibitor must be added to prevent gelation during the synthesis process.

Example 1: Aging states of the polymerization inhibitor tert-butylhydroquinone in TMPTA at different temperatures, with an addition level of 300 ppm:

  Aged for 2 days Aged for 4 days Aged for 6 days Aged for 8 days
80℃ OK OK OK OK
100℃ OK OK OK OK
120℃ OK OK Semi-gelation Gelation
140℃ OK Gelation / /

Conclusion: At a high temperature of 140℃, the polymerization inhibitor no longer has sufficient time to prevent free-radical polymerization, and its inhibitory effect is significantly reduced.

6. How to Control the Temperature in Synthetic Experiments

Controlling the temperature during synthesis experiments is crucial. The synthesis reaction of acrylates is an exothermic process; if the temperature is not properly controlled, the reactor may overheat, leading to severe consequences such as runaway polymerization.

Comparison chart of exothermic rates for synthesizing standard propylene glycol acrylate in volumetric flasks at 100℃:

Note: Using a 5L reaction vessel, a heating rate of 3°C per minute due to exothermic reactions is considered relatively rapid. Exceeding 3°C/min poses significant danger when the reactor is charged.

1. Control the amount of catalyst added.

The figure below shows a comparison of the decrease in acid value for the standard epoxy acrylate reaction after adding equal amounts of 500 ppm of each catalyst at the same temperature of 105℃.

The effect of catalysts on resin viscosity:

Example: The effect of triphenylphosphine dosage on the viscosity change of standard epoxy acrylate:

2. Control the reaction heating rate

According to List 3 and List 4, the higher the temperature, the faster the heat release rate. Therefore, to control the temperature, it is necessary to keep the heat release rate relatively low—specifically, during the exothermic stage at the onset of the reaction, the temperature should be maintained within a lower range.

7. The Effect of Temperature on Resin Viscosity

Example 1: Viscosity of standard epoxy acrylate at different temperatures:

Example 2: The effect of temperature on the viscosity of polyurethane acrylate:

The diisocyanate commonly used in polyurethane experiments is IPDI. Taking the reaction characteristics of IPDI as an example, we will illustrate the effect of temperature on the synthesis of polyurethane acrylates. Experimental conditions: At a fixed diisocyanate conversion rate, the selectivity toward different active isocyanate groups is determined by measuring the content of residual monomers. This selectivity is expressed as the ratio of the reaction rate constants k1 and k2. Experimental system: IPDI/n-butanol, with a molar ratio of isocyanate groups to hydroxyl groups of 2:1.

(1) Under catalyst-free conditions:

The ratio of the final viscosity to the reaction rate constant as a function of temperature is shown in the figure below.

The ratio of the reaction rate constants is 5.5 to 2.8.

(2) Add 0.075% dibutyltin dilaurate as a catalyst:

The ratio of the final viscosity to the reaction rate constant as a function of temperature is shown in the figure below.

Above 100℃, byproducts such as urea carbamate are formed.

8. The Effect of Temperature on the Photocuring Rate

Example 1: Temperature Variation During Photocuring of a Polyurethane Acrylate:

During the light-curing process, the temperature reaches a maximum of 70℃ and then begins to decrease, while the conversion rate increases steadily over time.

Example 2: The change in conversion rate and polymerization rate of a bisphenol A epoxy acrylate as a function of temperature:

(1) The conversion rate increases as the temperature rises;

(2) The polymerization rate initially increases with rising temperature, but above 85℃, it starts to decrease as the temperature continues to rise.

Reason: The viscosity of epoxy acrylate can decrease by two orders of magnitude from 25°C to 85°C. Before 85°C, the polymerization rate increases with rising temperature primarily because the reduced viscosity enhances molecular diffusion. After 85°C, the polymerization rate decreases with increasing temperature due to the intensified occurrence of chain termination and chain transfer reactions.

But the situation with monomers is different.

Example 3: TPGDA—between 25°C and 85°C, its viscosity decreases by less than one order of magnitude. The change in polymerization rate is related to the photoinitiator.

Initiator used in TPGDA Polymerization rate variation
369 The polymerization rate remains constant between 25 and 145℃.
907 The polymerization rate remains constant between 25 and 70°C, but decreases as the temperature rises above 70°C.
651 or 1173 The polymerization rate continuously decreases as temperature increases; no phenomenon of first increasing and then decreasing occurs.

Reason: At the wavelength used (313 nm), the extinction coefficients of photoinitiators 369 and 907 are two orders of magnitude higher than those of 651 and 1173. Consequently, the number of active free radicals generated is significantly greater, and thus their impact on terminating the reaction at high temperatures is also much more pronounced.

In general, the effect of temperature on photopolymerization reactions is rather complex and is influenced by other factors as well. However, the change in viscosity caused by temperature variations is likely the primary reason behind temperature’s impact on photopolymerization.

9. Tips

1. The lower temperature limit for the survival of life:

At -170℃, some simple microorganisms can still survive, such as Escherichia coli, Salmonella typhi, and Staphylococcus aureus.

2. Earth's lowest temperature:

At -129℃, the lowest temperature on Earth is recorded at Vinson Peak, the highest summit in Antarctica. The annual average temperature here is -129℃, and the average summer temperature is -117.7℃. Even Mount Everest, the world’s highest peak, has an average summer temperature of -45℃. This stark contrast vividly illustrates just how frigid the Antarctic region truly is.

3. The lowest temperature that an alcohol thermometer can measure:

At -117℃, the red liquid in the thermometer is alcohol—alcohol only begins to freeze at this temperature. Therefore, even in Antarctica, where temperatures are the lowest on Earth, alcohol thermometers can still be used. Of course, once the temperature drops below -117℃, alcohol thermometers become useless.

4. Lowest land temperature on Earth:

-88.3℃, measured in the interior of Antarctica.

5. The lowest temperature at which the SARS virus can survive in a low-temperature environment:

At -80℃, a notable characteristic of the SARS virus is that it is heat-sensitive but cold-resistant—even at -80℃, it can survive for at least 4 days, and sometimes as long as 21 days. In contrast, at 56℃, the SARS virus can survive for no more than 90 minutes.

6. Lowest temperature in the Arctic:

At -70℃, the average annual temperature in the Arctic region ranges from -15℃ to -20℃—25℃ higher than the average annual temperature in Antarctica. During winter (January), the polar night lasts for 180 days, and the lowest temperature can drop as low as -70℃. The cold climate helps prevent certain diseases. The Eskimos who live in the Arctic primarily subsist on seal meat and seal oil; as a result, local residents rarely suffer from heart disease, cardiovascular problems, hypertension, or arthritis.

7. China’s coldest temperature:

-52.3℃—on February 13, 1969, Mohe finally recorded the lowest-ever temperature ever documented in China’s current meteorological data: -52.3℃.

The flower that’s most resistant to cold in the world is the snow lotus, which grows in China and blooms beautifully even at -50℃.

8. Temperature range suitable for mosquito survival:

30℃—the temperature mosquitoes prefer most—is around 30℃. They can't tolerate temperatures much higher than that either. When autumn arrives and the weather cools down, with temperatures dropping below 10℃, they stop reproducing, cease feeding and become motionless, entering a state of hibernation until they're roused again in the following spring.

9. The human body’s own temperature limits:

At 42℃, humans, being homeothermic animals, generally remain within the temperature range of 35℃ to 42℃. At 41℃, the body’s organs—such as the liver, kidneys, and brain—will begin to malfunction. A high fever of 42℃ sustained for several consecutive days can be fatal even for adults.

10. The highest temperature ever recorded on Earth:

58℃—due to the sparse cloud cover, intense sunshine, and lack of vegetation in desert regions, coupled with low air humidity, daytime temperatures rise extremely rapidly. For most of the day, temperatures remain above 30℃, and at the hottest time around noon, they can soar above 50℃. In North Africa, a record high of 58℃ has been documented (Libya on September 13, 1922).

11. The optimal temperature for human taste perception:

At 70℃, research by physiologists and psychologists shows that the wide variety of taste sensations people experience when consuming food is, in essence, the result of the synergistic interaction between taste and smell. Certain hot beverages, such as coffee, are most delicious and flavorful precisely at a temperature of 70℃. Similarly, hot milk and hot dishes taste best when their temperature hovers around 70℃. For some fried foods, like fried shrimp, the ideal temperature should also be around 70℃. Although they may still feel slightly hot to the touch, it’s precisely at this temperature that their flavor is at its peak.

12. The highest temperature ever created by humans:

510,000,000℃—the highest temperature ever achieved by humans—is roughly 30 times hotter than the core of the Sun. This temperature was created on May 27, 1994, at the Princeton Plasma Physics Laboratory in Princeton, New Jersey, USA, using a tokamak fusion reactor that employed a plasma mixture of deuterium and tritium.

Share to:

Related News


Silicone Performance and Applications

Organosilicon compounds, or organosilicon substances, are compounds that contain Si-O bonds and have at least one organic group directly bonded to a silicon atom. By convention, compounds in which organic groups are linked to silicon atoms via oxygen, sulfur, nitrogen, or other elements are also often classified as organosilicon compounds. Among these, polysiloxanes—polymeric compounds whose backbone consists of siloxane linkages (-Si-O-Si-)—represent the largest and most extensively studied and widely used class of organosilicon compounds, accounting for more than 90% of the total usage.


Collection of Light-Curing Coating and Ink Formulations

Light-curing coatings and inks are materials that harden by absorbing ultraviolet (UV) radiation energy. They consist of resins, monomers, photoinitiators, and other additives, which, when exposed to UV light, form a strong and durable coating or printed image.


Introduction to the Main Raw Materials and Synthesis Overview of Light-Curing Resins

The main raw materials for light-curable resins include epoxy acrylates and polyurethane acrylates. Among these, epoxy acrylates can be categorized into: bisphenol A-type epoxies; phenolic epoxies; and o-methylphenolic epoxies. Polyurethane acrylates can be categorized into: polyether polyols; polyester diols; and polycarbonate diols.